This work explores a spatial printing method to fabricate continuous fiber-reinforced thermoplastic composites (CFRTPCs), which can achieve exceptional mechanical performance. For models giving complex 3D stress distribution under loads, typical planar-layer based fiber placement usually fails to provide sufficient reinforcement due to their orientations being constrained to planes. The effectiveness of fiber reinforcement could be maximized by using multi-axis additive manufacturing (MAAM) to better control the orientation of continuous fibers in 3D-printed composites. Here, we propose a computational approach to generate 3D toolpaths that satisfy two major reinforcement objectives: (1) following the maximal stress directions in critical regions and (2) connecting multiple load-bearing regions by continuous fibers. Principal stress lines are first extracted in an input solid model to identify critical regions. Curved layers aligned with maximal stresses in these critical regions are generated by computing an optimized scalar field and extracting its iso-surfaces. Then, topological analysis and operations are applied to each curved layer to generate a computational domain that preserves fiber continuity between load-bearing regions. Lastly, continuous fiber toolpaths aligned with maximal stresses are generated on each surface layer by computing an optimized scalar field and extracting its iso-curves. A hardware system with dual robotic arms is employed to conduct the physical MAAM tasks depositing polymer or fiber reinforced polymer composite materials by applying a force normal to the extrusion plane to aid consolidation. When comparing to planar-layer based printing results in tension, up to 644% failure load and 240% stiffness are observed on shapes fabricated by our spatial printing method. We demonstrate the versatility of our approach through various complex load cases which demonstrate their successful implementation of continuous fiber printing in 3D.

In this paper, a deep learning framework combined with isogeometric analysis (IGA for short) called IGA-Reuse-Net is proposed for efficient reuse of numerical simulation on a set of topology-consistent models. Compared with previous data-driven numerical simulation methods only for simple computational domains, our method can predict high-accuracy PDE solutions over topology-consistent geometries with complex boundaries. UNet3+ architecture with interlaced sparse self-attention (ISSA) module is used to enhance the performance of the network. In addition, we propose a new loss function that combines a coefficients loss and a numerical solution loss. Several training datasets with topology-consistent models are constructed for the proposed framework. To verify the effectiveness of our approach, two different types of Poisson equations with different source functions are solved on three datasets with different topologies. Our framework can achieve a good trade-off between accuracy and efficiency. It outperforms the physics-informed neural network (PINN for short) model and yields promising results of prediction.

Soft robots can safely interact with environments because of their mechanical compliance. Self-collision is also employed in the modern design of soft robots to enhance their performance during different tasks. However, developing an efficient and reliable simulator that can handle the collision response well, is still a challenging task in the research of soft robotics. This paper presents a collision-aware simulator based on geometric optimization, in which we develop a highly efficient and realistic collision checking / response model incorporating a hyperelastic material property. Both actuated deformation and collision response for soft robots are formulated as geometry-based objectives. The collision-free body of a soft robot can be obtained by minimizing the geometry-based objective function. Unlike the FEA-based physical simulation, the proposed pipeline performs a much lower computational cost. Moreover, adaptive remeshing is applied to achieve the improvement of the convergence when dealing with soft robots that have large volume variations. Experimental tests are conducted on different soft robots to verify the performance of our approach.

This article presents an efficient learning-based method to solve the <italic>inverse kinematic</italic> (IK) problem on soft robots with highly nonlinear deformation. The major challenge of efficiently computing IK for such robots is due to the lack of analytical formulation for either forward or inverse kinematics. To address this challenge, we employ neural networks to learn both the mapping function of forward kinematics and also the Jacobian of this function. As a result, Jacobian-based iteration can be applied to solve the IK problem. A sim-to-real training transfer strategy is conducted to make this approach more practical. We first generate a large number of samples in a simulation environment for learning both the kinematic and the Jacobian networks of a soft robot design. Thereafter, a sim-to-real layer of differentiable neurons is employed to map the results of simulation to the physical hardware, where this sim-to-real layer can be learned from a very limited number of training samples generated on the hardware.

Reconstruction of high-fidelity 3D objects or scenes is a fundamental research problem. Recent advances in RGB-D fusion have demonstrated the potential of producing 3D models from consumer-level RGB-D cameras. However, due to the discrete nature and limited resolution of their surface representations (e.g., point or voxel based), existing approaches suffer from the accumulation of errors in camera tracking and distortion in the reconstruction, which leads to an unsatisfactory 3D reconstruction. In this article, we present a method using on-the-fly implicits of Hermite Radial Basis Functions (HRBFs) as a continuous surface representation for camera tracking in an existing RGB-D fusion framework. Furthermore, curvature estimation and confidence evaluation are coherently derived from the inherent surface properties of the on-the-fly HRBF implicits, which are devoted to a data fusion with better quality. We argue that our continuous but on-the-fly surface representation can effectively mitigate the impact of noise with its robustness and constrain the reconstruction with inherent surface smoothness when being compared with discrete representations. Experimental results on various real-world and synthetic datasets demonstrate that our HRBF-fusion outperforms the state-of-the-art approaches in terms of tracking robustness and reconstruction accuracy.

In this paper, we present a new computational pipeline for designing and fabricating 4D garments as knitwear that considers comfort during body movement. This is achieved by careful control of elasticity distribution to reduce uncomfortable pressure and unwanted sliding caused by body motion. We exploit the ability to knit patterns in different elastic levels by single-jersey jacquard (SJJ) with two yarns. We design the distribution of elasticity for a garment by physics-based computation, the optimized elasticity on the garment is then converted into instructions for a digital knitting machine by two algorithms proposed in this paper. Specifically, a graph-based algorithm is proposed to generate knittable stitch meshes that can accurately capture the 3D shape of a garment, and a tiling algorithm is employed to assign SJJ patterns on the stitch mesh to realize the designed distribution of elasticity. The effectiveness of our approach is verified on simulation results and on specimens physically fabricated by knitting machines.

We present a field-based method of toolpath generation for 3D printing continuous fibre reinforced thermoplastic composites. Our method employs the strong anisotropic material property of continuous fibres by generating toolpaths along the directions of tensile stresses in the critical regions. Moreover, the density of toolpath distribution is controlled in an adaptive way proportionally to the values of stresses. Specifically, a vector field is generated from the stress tensors under given loads and processed to have better compatibility between neighboring vectors. An optimal scalar field is computed later by making its gradients approximate the vector field. After that, isocurves of the scalar field are extracted to generate the toolpaths for continuous fibre reinforcement, which are also integrated with the boundary conformal toolpaths in user selected regions. The performance of our method has been verified on a variety of models in different loading conditions. Experimental tests are conducted on specimens by 3D printing continuous carbon fibres (CCF) in a polylactic acid (PLA) matrix. Compared to reinforcement by load-independent toolpaths, the specimens fabricated by our method show up to 71.4% improvement on the mechanical strength in physical tests when using the same (or even slightly smaller) amount of continuous fibres.

Using the raw data from consumer-level RGB-D cameras as input, we propose a deep-learning-based approach to efficiently generate RGB-D images with completed information in high resolution. To process the input images in low resolution with missing regions, new operators for adaptive convolution are introduced in our deep-learning network that consists of three cascaded modules - the completion module, the refinement module, and the super-resolution module. The completion module is based on an architecture of encoder-decoder, where the features of input raw RGB-D will be automatically extracted by the encoding layers of a deep neural network. The decoding layers are applied to reconstruct the completed depth map, which is followed by a refinement module to sharpen the boundary of different regions. For the super-resolution module, we generate RGB-D images in high resolution by multiple layers for feature extraction and a layer for upsampling. Benefited from the adaptive convolution operators proposed in this article, our results outperform the existing deep-learning-based approaches for RGB-D image complete and super-resolution. As an end-to-end approach, high-fidelity RGB-D images can be generated efficiently at the rate of 22 frames/s. Note to Practitioners - With the development of consumer-level RGB-D cameras, industries have started to employ these low-cost sensors in many robotic and automation applications. However, images generated by consumer-level RGB-D cameras are generally in low resolution. Moreover, the depth images often have incomplete regions when the surface of an object is transparent, highly reflective, or beyond the distance of sensing. With the help of our method, engineers are able to 'repair' the images captured by consumer-level RGB-D cameras in high efficiency. As the typical deep-learning networks are employed in this approach, the proposed approach fits well with the GPU-based hardware architecture of deep-learning computation - therefore, it potentially can be integrated into the hardware of RGB-D cameras.

Multi-axis additive manufacturing enables high flexibility of material deposition along dynamically varied directions. The Cartesian motion platforms of these machines include three parallel axes and two rotational axes. Singularity on rotational axes is a critical issue to be tackled in motion planning for ensuring high quality of manufacturing results. The highly nonlinear mapping in the singular region can convert a smooth toolpath with uniformly sampled waypoints defined in the model coordinate system into a highly discontinuous motion in the machine coordinate system, which leads to over-extrusion/under-extrusion of materials in filament-based additive manufacturing. The problem is challenging as both the maximal and the minimal speeds at the tip of a printer head must be controlled in motion. Moreover, collision may occur when sampling-based collision avoidance is employed. In this letter, we present a motion planning method to support the manufacturing realization of designed toolpaths for multi-axis additive manufacturing. Problems of singularity and collision are considered in an integrated manner to improve the motion therefore the quality of fabrication.

The following sections are included: • Introduction • Literature Review • Direct Deposition: Our Study • Results • Electrical Conductivity • Discussion • Summary • Acknowledgment • References.

Silicones have desirable properties such as skin-safety, high temperature-resistance, and flexibility. Many applications require the presence of a hard body connected to the silicone. Traditionally, it has been difficult to create strong bonding between silicones and hard materials. In this study, a technique is presented to control the bonding strength between silicones and thermoplastics through mechanical interlocking. This is realized through a hybrid fabrication method where silicone is cast onto a 3D-printed mold and interlocking structure. The influence of the structure's design parameters on the bonding strength is explored through theoretical modeling and physical testing, while the manufacturability of the 3D-printed structure is ensured. A CAD tool is developed to automatically apply the interlocking structure to product surfaces. The user interface visualizes the theoretical strength of the cells as the designer adjusts the cell parameters, allowing the designer to iteratively optimize the structure to the product's load case. The bonding strength of the presented mechanical interlocking structure is more than 5.5 times higher than can be achieved with a commercially available primer. The presented technique enables custom digital design and manufacturing of durable free-form parts. This is demonstrated through application of the technique in over-molded products, airtight seals, and soft pneumatic actuators.

The anisotropy of mechanical strength on a 3D printed model can be controlled in a multi-axis 3D printing system as materials can be accumulated along dynamically varied directions. In this paper, we present a new computational framework to generate specially designed layers and toolpaths of multi-axis 3D printing for strengthening a model by aligning filaments along the directions with large stresses. The major challenge comes from how to effectively decompose a solid into a sequence of strength-aware and collision-free working surfaces. We formulate it as a problem to compute an optimized governing field together with a selected orientation of fabrication setup. Iso-surfaces of the governing field are extracted as working surface layers for filament alignment. Supporting structures in curved layers are constructed by extrapolating the governing field to enable the fabrication of overhangs. Compared with planar-layer based Fused Deposition Modeling (FDM) technology, models fabricated by our method can withstand up to 6.35× loads in experimental tests.

3D printing techniques such as Fused Deposition Modeling (FDM) have enabled the fabrication of complex geometry quickly and cheaply. Objects are produced by filling (a portion of) the 2D polygons of consecutive layers with contour-parallel extrusion toolpaths. Uniform width toolpaths consisting of inward offsets from the outline polygons produce over- and underfill regions in the center of the shape, which are especially detrimental to the mechanical performance of thin parts. In order to fill shapes with arbitrary diameter densely the toolpaths require adaptive width. Existing approaches for generating toolpaths with adaptive width result in a large variation in widths, which for some hardware systems is difficult to realize accurately. In this paper we present a framework which supports multiple schemes to generate toolpaths with adaptive width, by employing a function to decide the number of beads and their widths. Furthermore, we propose a novel scheme which reduces extreme bead widths, while limiting the number of altered toolpaths. We statistically validate the effectiveness of our framework and this novel scheme on a data set of representative 3D models, and physically validate it by developing a technique, called back pressure compensation, for off-the-shelf FDM systems to effectively realize adaptive width.

We present a method for effectively planning the motion trajectory of robots in manufacturing tasks, the tool paths of which are usually complex and have a large number of discrete time constraints as waypoints. Kinematic redundancy also exists in these robotic systems. The jerk of motion is optimized in our trajectory planning method at the meanwhile of fabrication process to improve the quality of fabrication. Our method is based on a sampling strategy and consists of two major parts. After determining an initial path by graph search, a greedy algorithm is adopted to optimize a path by locally applying adaptive filers in the regions with large jerks. The filtered result is obtained by numerical optimization. In order to achieve efficient computation, an adaptive sampling method is developed for learning a collision-indication function that is represented as a support-vector machine. Applications in robot-Assisted 3-D printing are given in this article to demonstrate the functionality of our approach. Note to Practitioners-In robot-Assisted manufacturing applications, robotic arms are employed to realize the motion of workpieces (or machining tools) specified as a sequence of waypoints with the positions of tool tip and the tool orientations constrained. The required degree of freedom (DOF) is often less than the robotic hardware system (e.g., a robotic arm has six-DOF). Specifically, rotations of the workpiece around the axis of a tool can be arbitrary (see Fig. 1 for an example). By using this redundancy, i.e., there are many possible poses of a robotic arm to realize a given waypoint, the trajectory of robots can be optimized to consider the performance of motion in velocity, acceleration, and jerk in the joint space. In addition, when fabricating complex models, each tool path can have a large amount of waypoints. It is crucial for a motion planning algorithm to compute a smooth and collision-free trajectory of robot to improve the fabrication quality. The time taken by the planning algorithm should not significantly lengthen the total manufacturing time; ideally, it would remain hidden as computing motions for a layer can be done while the previous layer is printing. The method presented in this article provides an efficient framework to tackle this problem. The framework has been well tested on our robot-Assisted additive manufacturing system to demonstrate its effectiveness and can be generally applied to other robot-Assisted manufacturing systems.

Robots fabricated with soft materials can provide higher flexibility and, thus, better safety while interacting in unpredictable situations. However, the usage of soft material makes it challenging to predict the deformation of a continuum body under actuation and, therefore, brings difficulty to the kinematic control of its movement. In this article, we present a geometry-based framework for computing the deformation of soft robots within the range of linear material elasticity. After formulating both manipulators and actuators as geometry elements, deformation can be efficiently computed by solving a constrained optimization problem. Because of its efficiency, forward and inverse kinematics for soft manipulators can be solved by an iterative algorithm with a low computational cost. Meanwhile, components with multiple materials can also be geometrically modeled in our framework with the help of a simple calibration. Numerical and physical experimental tests are conducted on soft manipulators driven by different actuators with large deformation to demonstrate the performance of our approach.

We present a method for fabricating general models with multi-directional 3-D printing systems by printing different model regions along with different directions. The core of our method is a support-effective volume decomposition algorithm that minimizes the area of the regions with large overhangs. A beam-guided searching algorithm with manufacturing constraints determines the optimal volume decomposition, which is represented by a sequence of clipping planes. While current approaches require manually assembling separate components into a final model, our algorithm allows for directly printing the final model in a single pass. It can also be applied to models with loops and handles. A supplementary algorithm generates special supporting structures for models where supporting structures for large overhangs cannot be eliminated. We verify the effectiveness of our method using two hardware systems: a Cartesian-motion-based system and an angular-motion-based system. A variety of 3-D models have been successfully fabricated on these systems. Note to Practitioners - In conventional planar-layer-based 3-D printing systems, supporting structures need to be added at the bottom of large overhanging regions to prevent material collapse. Supporting structures used in single-material 3-D printing technologies have three major problems: being difficult to remove, introducing surface damage, and wasting material. This article introduces a method to improve 3-D printing by adding rotation during the manufacturing process. To keep the hardware system relatively inexpensive, the hardware, called a multi-directional 3-D printing system, only needs to provide unsynchronized rotations. In this system, models are subdivided into different regions, and then, the regions are printed in different directions. We develop a general volume decomposition algorithm for effectively reducing the area that needs supporting structures. When supporting structures cannot be eliminated, we provide a supplementary algorithm for generating supports compatible with multi-directional 3-D printing. Our method can speed up the process of 3-D printing by saving time in producing and removing supports.

Microstructures with spatially-varying properties such as trabecular bone are widely seen in nature. These functionally graded materials possess smoothly changing microstructural topologies that enable excellent micro and macroscale performance. The fabrication of such microstructural materials is now enabled by additive manufacturing (AM). A challenging aspect in the computational design of such materials is ensuring compatibility between adjacent microstructures. Existing works address this problem by ensuring geometric connectivity between adjacent microstructural unit cells. In this paper, we aim to find the optimal connectivity between topology optimized microstructures. Recognizing the fact that the optimality of connectivity can be evaluated by the resulting physical properties of the assemblies, we propose to consider the assembly of adjacent cells together with the optimization of individual cells. In particular, our method simultaneously optimizes the physical properties of the individual cells as well as those of neighbouring pairs, to ensure material connectivity and smoothly varying physical properties. We demonstrate the application of our method in the design of functionally graded materials for implant design (including an implant prototype made by AM), and in the multiscale optimization of structures.

For grasping (unknown) objects, soft pneumatic actuators are primarily designed to bend towards a specific direction. Due to the flexibility of material and structure, soft actuators are also prone to out-of-plane deformations including twisting and sidewards bending, especially if the loading is asymmetric. In this paper, we demonstrate the negative effects of out-of-plane deformation on grasping. A structural design is proposed to reduce this type of deformation and thus improve grasping stability. Comparisons are first performed on soft pneumatic actuators with the same bending stiffness but different resistances to out-of-plane deformation, which is realized by changing the cross-section of the inextensible layer. To reduce out-of-plane deformation, a stiffening structure inspired by spatial flexures is integrated into the soft actuator. The integrated design is 3D printed using a single material. Physical experiments have been conducted to verify the improved grasping stability.

2D coil design limits the use of wireless power transfer (WPT) in many products with freeform outer shapes. In this paper, enabled by 3D printed electronics, we propose a systematic approach to design and fabricate 3D coils for WPT. Based on the circular spiral and rectangular spiral patterns, 3D receiver and transmitter coils can be generated on an arbitrarily selected region of a product and its offset, respectively. Mathematical models are proposed to estimate the self-inductance and the mutual-inductance of the 3D arbitrarily shaped coils for 3D WPT. This leads to a new design approach of a 3D WPT system. Several sets of 3D printed WPT systems were designed, simulated, and prototyped to demonstrate the effectiveness of the proposed design approach as well as the mathematical models. The calculation speed of the proposed mathematical models is 30 times faster than the simulation, and compared with the measurement results, the calculation results have mean absolute errors of 2.63% and 4.45% regarding the self- and the mutual-inductance, where the simulation results have mean absolute errors of 1.20% and 2.38%, respectively. Measurements also indicate that with a 5V input, the prototypes are able to deliver 1-watt power at an efficiency ranging between 20.9% and 25.3%. It was concluded that the proposed approach is feasible and promising for designing and manufacturing WPT using 3D printed electronics.

Actuators using soft materials feature a large number of degrees of freedom. This tremendous flexibility allows a soft actuator to passively adapt its shape to the objects under interaction. In this paper, we propose a novel proprioception method for soft actuators during real-time interaction with previously unknown objects. First, we design a color-based sensing structure that instantly translates the inflation of a bellow into changes in color, which are subsequently detected by a miniaturized color sensor. The color sensor is small and, thus, multiple of them can be integrated into soft pneumatic actuators to reflect local deformations. Second, we make use of a feed-forward neural network to reconstruct a multivariate global shape deformation from local color signals. Our results demonstrate that deformations of the actuator during interaction, including sigmoid-like shapes, can be accurately reconstructed. The accurate shape sensing represents a significant step toward closed-loop control of soft robots in unstructured environments.