A large-scale spanwise and wall-normal array of sonic anemometers in the atmospheric surface layer is used to acquire all three components of instantaneous fluctuating velocity as well as temperature in a range of stability conditions. These data permit investigation of the three-dimensional statistical structure of turbulence structures. Based on a similar dataset, Krug et al. (Boundary-Layer Meteorol., vol. 172, 2019, pp. 199-214) reported a self-similar range of wall-attached turbulence structures under both unstable and near-neutral stability conditions. They considered only a wall-normal array and thus assessed statistical structure in the wall-normal direction, in relation to the streamwise wavelength. The present work extends the view of a self-similar range of turbulence structures, by including the statistical structure in the spanwise direction. Moreover, by analysing the phase shift between synchronized measurements in the spectral domain, it is inferred how a scale-dependent inclination angle in the streamwise/wall-normal plane varies with stability. Results suggest that the self-similar wall-attached structures have similar aspect ratios between streamwise/wall-normal scales and streamwise/spanwise scales such that for both near-neutral and unstable conditions. Under the most unstable conditions, coherent structures with are inclined at angles as high as relative to the solid boundary, while larger scales exhibit inclination angles of approximately. For near-neutral stability conditions, the angle tends towards for all scales. It is noted that in the near-neutral condition, the structure inclination angle and the aspect ratio - and thus the statistical modelling of coherent structures in the atmospheric surface layer - are highly sensitive to the value of the stability parameter.@en

This study presents an experimental dataset documenting the evolution of a turbulent boundary layer downstream of a rough-to-smooth surface transition. To investigate the effect of upstream flow conditions, two groups of experiments are conducted. For the Group-Re cases, a nominally constant viscous-scaled equivalent sand grain roughness is maintained on the rough surface, while the friction Reynolds number ranges from 7100 to 21 000. For the Group-ks cases, is maintained while ranges from 111 to 228. The wall-shear stress on the downstream smooth surface is measured directly using oil-film interferometry to redress previously reported uncertainties in the skin-friction coefficient recovery trends. In the early development following the roughness transition, the flow in the internal layer is not in equilibrium with the wall-shear stress. This conflicts with the common practise of modelling the mean velocity profile as two log laws below and above the internal layer height, as first proposed by Elliott (Trans. Am. Geophys. Union, vol. 39, 1958, pp. 1048-1054). As a solution to this, the current data are used to model the recovering mean velocity semi-empirically by blending the corresponding rough-wall and smooth-wall profiles. The over-energised large-scale motions leave a strong footprint in the near-wall region of the energy spectrum, the frequency and magnitude of which exhibit dependence on and, respectively. The energy distribution in near-wall small scales is mostly unaffected by the presence of the outer flow with rough-wall characteristics, which can be used as a surrogate measure to extract the local friction velocity.@en

This study presents an experimental dataset documenting the evolution of a turbulent boundary layer downstream of a rough-to-smooth surface transition. To investigate the effect of upstream flow conditions, two groups of experiments are conducted. For the Group-Re cases, a nominally constant viscous-scaled equivalent sand grain roughness is maintained on the rough surface, while the friction Reynolds number ranges from 7100 to 21 000. For the Group-ks cases, is maintained while ranges from 111 to 228. The wall-shear stress on the downstream smooth surface is measured directly using oil-film interferometry to redress previously reported uncertainties in the skin-friction coefficient recovery trends. In the early development following the roughness transition, the flow in the internal layer is not in equilibrium with the wall-shear stress. This conflicts with the common practise of modelling the mean velocity profile as two log laws below and above the internal layer height, as first proposed by Elliott (Trans. Am. Geophys. Union, vol. 39, 1958, pp. 1048-1054). As a solution to this, the current data are used to model the recovering mean velocity semi-empirically by blending the corresponding rough-wall and smooth-wall profiles. The over-energised large-scale motions leave a strong footprint in the near-wall region of the energy spectrum, the frequency and magnitude of which exhibit dependence on and, respectively. The energy distribution in near-wall small scales is mostly unaffected by the presence of the outer flow with rough-wall characteristics, which can be used as a surrogate measure to extract the local friction velocity.@en

In this study, we develop an analytical model to predict the turbulent boundary layer downstream of a step-change in the surface roughness where upstream flow conditions are given. We first revisit the classical model of Elliott (Trans. Am. Geophys. Union, vol. 39, 1958, pp. 1048-1054), who modelled the velocity distribution within and above the internal layer with a simple piecewise logarithmic profile, and evolved the velocity profile using the streamwise momentum equation. Elliott's model was originally developed for an atmospheric surface layer, and to make the model applicable to a spatially developing turbulent boundary layer with finite thickness, we propose a number of more physical refinements, including adding a wake function to the velocity profile, considering the growth of the entire boundary layer in the streamwise direction, and using a more realistic shear stress profile in the momentum equation. In particular, we implement the blending model (Li et al., J. Fluid Mech., vol. 923, 2021, p. A18) to account for the deviation of the mean flow within the internal layer from a canonical velocity profile based on the local wall condition. These refinements lead to improved agreement between the prediction and the measurement, especially in the vicinity of the rough-to-smooth change.@en

In this study, we develop an analytical model to predict the turbulent boundary layer downstream of a step-change in the surface roughness where upstream flow conditions are given. We first revisit the classical model of Elliott (Trans. Am. Geophys. Union, vol. 39, 1958, pp. 1048-1054), who modelled the velocity distribution within and above the internal layer with a simple piecewise logarithmic profile, and evolved the velocity profile using the streamwise momentum equation. Elliott's model was originally developed for an atmospheric surface layer, and to make the model applicable to a spatially developing turbulent boundary layer with finite thickness, we propose a number of more physical refinements, including adding a wake function to the velocity profile, considering the growth of the entire boundary layer in the streamwise direction, and using a more realistic shear stress profile in the momentum equation. In particular, we implement the blending model (Li et al., J. Fluid Mech., vol. 923, 2021, p. A18) to account for the deviation of the mean flow within the internal layer from a canonical velocity profile based on the local wall condition. These refinements lead to improved agreement between the prediction and the measurement, especially in the vicinity of the rough-to-smooth change.@en

In this study, we develop an analytical model to predict the turbulent boundary layer downstream of a step-change in the surface roughness where upstream flow conditions are given. We first revisit the classical model of Elliott (Trans. Am. Geophys. Union, vol. 39, 1958, pp. 1048-1054), who modelled the velocity distribution within and above the internal layer with a simple piecewise logarithmic profile, and evolved the velocity profile using the streamwise momentum equation. Elliott's model was originally developed for an atmospheric surface layer, and to make the model applicable to a spatially developing turbulent boundary layer with finite thickness, we propose a number of more physical refinements, including adding a wake function to the velocity profile, considering the growth of the entire boundary layer in the streamwise direction, and using a more realistic shear stress profile in the momentum equation. In particular, we implement the blending model (Li et al., J. Fluid Mech., vol. 923, 2021, p. A18) to account for the deviation of the mean flow within the internal layer from a canonical velocity profile based on the local wall condition. These refinements lead to improved agreement between the prediction and the measurement, especially in the vicinity of the rough-to-smooth change.@en

In this study, we develop an analytical model to predict the turbulent boundary layer downstream of a step-change in the surface roughness where upstream flow conditions are given. We first revisit the classical model of Elliott (Trans. Am. Geophys. Union, vol. 39, 1958, pp. 1048-1054), who modelled the velocity distribution within and above the internal layer with a simple piecewise logarithmic profile, and evolved the velocity profile using the streamwise momentum equation. Elliott's model was originally developed for an atmospheric surface layer, and to make the model applicable to a spatially developing turbulent boundary layer with finite thickness, we propose a number of more physical refinements, including adding a wake function to the velocity profile, considering the growth of the entire boundary layer in the streamwise direction, and using a more realistic shear stress profile in the momentum equation. In particular, we implement the blending model (Li et al., J. Fluid Mech., vol. 923, 2021, p. A18) to account for the deviation of the mean flow within the internal layer from a canonical velocity profile based on the local wall condition. These refinements lead to improved agreement between the prediction and the measurement, especially in the vicinity of the rough-to-smooth change.@en

In this study, we develop an analytical model to predict the turbulent boundary layer downstream of a step-change in the surface roughness where upstream flow conditions are given. We first revisit the classical model of Elliott (Trans. Am. Geophys. Union, vol. 39, 1958, pp. 1048-1054), who modelled the velocity distribution within and above the internal layer with a simple piecewise logarithmic profile, and evolved the velocity profile using the streamwise momentum equation. Elliott's model was originally developed for an atmospheric surface layer, and to make the model applicable to a spatially developing turbulent boundary layer with finite thickness, we propose a number of more physical refinements, including adding a wake function to the velocity profile, considering the growth of the entire boundary layer in the streamwise direction, and using a more realistic shear stress profile in the momentum equation. In particular, we implement the blending model (Li et al., J. Fluid Mech., vol. 923, 2021, p. A18) to account for the deviation of the mean flow within the internal layer from a canonical velocity profile based on the local wall condition. These refinements lead to improved agreement between the prediction and the measurement, especially in the vicinity of the rough-to-smooth change.@en

In this study, we develop an analytical model to predict the turbulent boundary layer downstream of a step-change in the surface roughness where upstream flow conditions are given. We first revisit the classical model of Elliott (Trans. Am. Geophys. Union, vol. 39, 1958, pp. 1048-1054), who modelled the velocity distribution within and above the internal layer with a simple piecewise logarithmic profile, and evolved the velocity profile using the streamwise momentum equation. Elliott's model was originally developed for an atmospheric surface layer, and to make the model applicable to a spatially developing turbulent boundary layer with finite thickness, we propose a number of more physical refinements, including adding a wake function to the velocity profile, considering the growth of the entire boundary layer in the streamwise direction, and using a more realistic shear stress profile in the momentum equation. In particular, we implement the blending model (Li et al., J. Fluid Mech., vol. 923, 2021, p. A18) to account for the deviation of the mean flow within the internal layer from a canonical velocity profile based on the local wall condition. These refinements lead to improved agreement between the prediction and the measurement, especially in the vicinity of the rough-to-smooth change.@en

This paper examines the recovery of the wall-shear stress of a turbulent boundary layer that has undergone a sudden transition from a rough to a smooth surface. Early work of Antonia & Luxton (J. Fluid Mech., vol. 53, 1972, pp. 737-757) questioned the reliability of standard smooth-wall methods for measuring wall-shear stress in such conditions, and subsequent studies show significant disagreement depending on the approach used to determine the wall-shear stress downstream. Here we address this by utilising a collection of experimental databases at that have access to both 'direct' and 'indirect' measures of the wall-shear stress to understand the recovery to equilibrium conditions of the new surface. Our results reveal that the viscous region recovers almost immediately to an equilibrium state with the new wall conditions; however, the buffer region and beyond takes several boundary layer thicknesses before recovering to equilibrium conditions, which is longer than previously thought. A unique direct numerical simulation database of a wall-bounded flow with a rough-to-smooth wall transition is employed to confirm these findings. In doing so, we present evidence that any estimate of the wall-shear stress from the mean velocity profile in the buffer region or further away from the wall tends to underestimate its magnitude in the near vicinity of the rough-to-smooth transition, and this is likely to be partly responsible for the large scatter of recovery lengths to equilibrium conditions reported in the literature. Our results also reveal that smaller energetic scales in the near-wall region recover to an equilibrium state associated with the new wall conditions within one boundary layer thickness downstream of the transition, while larger energetic scales exhibit an over-energised state for several boundary layer thicknesses downstream of the transition. Based on these observations, an alternative approach to estimating the wall-shear stress from the premultiplied energy spectrum is proposed.@en

This paper examines the recovery of the wall-shear stress of a turbulent boundary layer that has undergone a sudden transition from a rough to a smooth surface. Early work of Antonia & Luxton (J. Fluid Mech., vol. 53, 1972, pp. 737-757) questioned the reliability of standard smooth-wall methods for measuring wall-shear stress in such conditions, and subsequent studies show significant disagreement depending on the approach used to determine the wall-shear stress downstream. Here we address this by utilising a collection of experimental databases at that have access to both 'direct' and 'indirect' measures of the wall-shear stress to understand the recovery to equilibrium conditions of the new surface. Our results reveal that the viscous region recovers almost immediately to an equilibrium state with the new wall conditions; however, the buffer region and beyond takes several boundary layer thicknesses before recovering to equilibrium conditions, which is longer than previously thought. A unique direct numerical simulation database of a wall-bounded flow with a rough-to-smooth wall transition is employed to confirm these findings. In doing so, we present evidence that any estimate of the wall-shear stress from the mean velocity profile in the buffer region or further away from the wall tends to underestimate its magnitude in the near vicinity of the rough-to-smooth transition, and this is likely to be partly responsible for the large scatter of recovery lengths to equilibrium conditions reported in the literature. Our results also reveal that smaller energetic scales in the near-wall region recover to an equilibrium state associated with the new wall conditions within one boundary layer thickness downstream of the transition, while larger energetic scales exhibit an over-energised state for several boundary layer thicknesses downstream of the transition. Based on these observations, an alternative approach to estimating the wall-shear stress from the premultiplied energy spectrum is proposed.@en

This paper examines the recovery of the wall-shear stress of a turbulent boundary layer that has undergone a sudden transition from a rough to a smooth surface. Early work of Antonia & Luxton (J. Fluid Mech., vol. 53, 1972, pp. 737-757) questioned the reliability of standard smooth-wall methods for measuring wall-shear stress in such conditions, and subsequent studies show significant disagreement depending on the approach used to determine the wall-shear stress downstream. Here we address this by utilising a collection of experimental databases at that have access to both 'direct' and 'indirect' measures of the wall-shear stress to understand the recovery to equilibrium conditions of the new surface. Our results reveal that the viscous region recovers almost immediately to an equilibrium state with the new wall conditions; however, the buffer region and beyond takes several boundary layer thicknesses before recovering to equilibrium conditions, which is longer than previously thought. A unique direct numerical simulation database of a wall-bounded flow with a rough-to-smooth wall transition is employed to confirm these findings. In doing so, we present evidence that any estimate of the wall-shear stress from the mean velocity profile in the buffer region or further away from the wall tends to underestimate its magnitude in the near vicinity of the rough-to-smooth transition, and this is likely to be partly responsible for the large scatter of recovery lengths to equilibrium conditions reported in the literature. Our results also reveal that smaller energetic scales in the near-wall region recover to an equilibrium state associated with the new wall conditions within one boundary layer thickness downstream of the transition, while larger energetic scales exhibit an over-energised state for several boundary layer thicknesses downstream of the transition. Based on these observations, an alternative approach to estimating the wall-shear stress from the premultiplied energy spectrum is proposed.@en

This paper examines the recovery of the wall-shear stress of a turbulent boundary layer that has undergone a sudden transition from a rough to a smooth surface. Early work of Antonia & Luxton (J. Fluid Mech., vol. 53, 1972, pp. 737-757) questioned the reliability of standard smooth-wall methods for measuring wall-shear stress in such conditions, and subsequent studies show significant disagreement depending on the approach used to determine the wall-shear stress downstream. Here we address this by utilising a collection of experimental databases at that have access to both 'direct' and 'indirect' measures of the wall-shear stress to understand the recovery to equilibrium conditions of the new surface. Our results reveal that the viscous region recovers almost immediately to an equilibrium state with the new wall conditions; however, the buffer region and beyond takes several boundary layer thicknesses before recovering to equilibrium conditions, which is longer than previously thought. A unique direct numerical simulation database of a wall-bounded flow with a rough-to-smooth wall transition is employed to confirm these findings. In doing so, we present evidence that any estimate of the wall-shear stress from the mean velocity profile in the buffer region or further away from the wall tends to underestimate its magnitude in the near vicinity of the rough-to-smooth transition, and this is likely to be partly responsible for the large scatter of recovery lengths to equilibrium conditions reported in the literature. Our results also reveal that smaller energetic scales in the near-wall region recover to an equilibrium state associated with the new wall conditions within one boundary layer thickness downstream of the transition, while larger energetic scales exhibit an over-energised state for several boundary layer thicknesses downstream of the transition. Based on these observations, an alternative approach to estimating the wall-shear stress from the premultiplied energy spectrum is proposed.@en

This paper examines the recovery of the wall-shear stress of a turbulent boundary layer that has undergone a sudden transition from a rough to a smooth surface. Early work of Antonia & Luxton (J. Fluid Mech., vol. 53, 1972, pp. 737-757) questioned the reliability of standard smooth-wall methods for measuring wall-shear stress in such conditions, and subsequent studies show significant disagreement depending on the approach used to determine the wall-shear stress downstream. Here we address this by utilising a collection of experimental databases at that have access to both 'direct' and 'indirect' measures of the wall-shear stress to understand the recovery to equilibrium conditions of the new surface. Our results reveal that the viscous region recovers almost immediately to an equilibrium state with the new wall conditions; however, the buffer region and beyond takes several boundary layer thicknesses before recovering to equilibrium conditions, which is longer than previously thought. A unique direct numerical simulation database of a wall-bounded flow with a rough-to-smooth wall transition is employed to confirm these findings. In doing so, we present evidence that any estimate of the wall-shear stress from the mean velocity profile in the buffer region or further away from the wall tends to underestimate its magnitude in the near vicinity of the rough-to-smooth transition, and this is likely to be partly responsible for the large scatter of recovery lengths to equilibrium conditions reported in the literature. Our results also reveal that smaller energetic scales in the near-wall region recover to an equilibrium state associated with the new wall conditions within one boundary layer thickness downstream of the transition, while larger energetic scales exhibit an over-energised state for several boundary layer thicknesses downstream of the transition. Based on these observations, an alternative approach to estimating the wall-shear stress from the premultiplied energy spectrum is proposed.@en

This paper examines the recovery of the wall-shear stress of a turbulent boundary layer that has undergone a sudden transition from a rough to a smooth surface. Early work of Antonia & Luxton (J. Fluid Mech., vol. 53, 1972, pp. 737-757) questioned the reliability of standard smooth-wall methods for measuring wall-shear stress in such conditions, and subsequent studies show significant disagreement depending on the approach used to determine the wall-shear stress downstream. Here we address this by utilising a collection of experimental databases at that have access to both 'direct' and 'indirect' measures of the wall-shear stress to understand the recovery to equilibrium conditions of the new surface. Our results reveal that the viscous region recovers almost immediately to an equilibrium state with the new wall conditions; however, the buffer region and beyond takes several boundary layer thicknesses before recovering to equilibrium conditions, which is longer than previously thought. A unique direct numerical simulation database of a wall-bounded flow with a rough-to-smooth wall transition is employed to confirm these findings. In doing so, we present evidence that any estimate of the wall-shear stress from the mean velocity profile in the buffer region or further away from the wall tends to underestimate its magnitude in the near vicinity of the rough-to-smooth transition, and this is likely to be partly responsible for the large scatter of recovery lengths to equilibrium conditions reported in the literature. Our results also reveal that smaller energetic scales in the near-wall region recover to an equilibrium state associated with the new wall conditions within one boundary layer thickness downstream of the transition, while larger energetic scales exhibit an over-energised state for several boundary layer thicknesses downstream of the transition. Based on these observations, an alternative approach to estimating the wall-shear stress from the premultiplied energy spectrum is proposed.@en

This paper examines the recovery of the wall-shear stress of a turbulent boundary layer that has undergone a sudden transition from a rough to a smooth surface. Early work of Antonia & Luxton (J. Fluid Mech., vol. 53, 1972, pp. 737-757) questioned the reliability of standard smooth-wall methods for measuring wall-shear stress in such conditions, and subsequent studies show significant disagreement depending on the approach used to determine the wall-shear stress downstream. Here we address this by utilising a collection of experimental databases at that have access to both 'direct' and 'indirect' measures of the wall-shear stress to understand the recovery to equilibrium conditions of the new surface. Our results reveal that the viscous region recovers almost immediately to an equilibrium state with the new wall conditions; however, the buffer region and beyond takes several boundary layer thicknesses before recovering to equilibrium conditions, which is longer than previously thought. A unique direct numerical simulation database of a wall-bounded flow with a rough-to-smooth wall transition is employed to confirm these findings. In doing so, we present evidence that any estimate of the wall-shear stress from the mean velocity profile in the buffer region or further away from the wall tends to underestimate its magnitude in the near vicinity of the rough-to-smooth transition, and this is likely to be partly responsible for the large scatter of recovery lengths to equilibrium conditions reported in the literature. Our results also reveal that smaller energetic scales in the near-wall region recover to an equilibrium state associated with the new wall conditions within one boundary layer thickness downstream of the transition, while larger energetic scales exhibit an over-energised state for several boundary layer thicknesses downstream of the transition. Based on these observations, an alternative approach to estimating the wall-shear stress from the premultiplied energy spectrum is proposed.@en

We investigate the underlying physics behind the change in amplitude modulation coefficient in noncanonical wall-bounded flows in the framework of the inner-outer interaction model (IOIM) [Baars, Phys. Rev. Fluids 1, 054406 (2016)2469-990X10.1103/PhysRevFluids.1.054406]. The IOIM captures the amplitude modulation effect, and here we focus on extending the model to noncanonical flows. An analytical relationship between the amplitude modulation coefficient and IOIM parameters is derived, which is shown to capture the increasing trend of the amplitude modulation coefficient with an increasing Reynolds number in a smooth-wall dataset. This relationship is then applied to classify and interpret the noncanonical turbulent boundary layer results reported in previous works. We further present the case study of a turbulent boundary layer after a rough-to-smooth change. Both single-probe and two-probe hotwire measurements are performed to acquire streamwise velocity time series in the recovering flow on the downstream smooth wall. An increased coherence between the large-scale motions and the small-scale envelope in the near-wall region is attributed to the stronger footprints of the overenergetic large-scale motions in the outer layer, whereas the near-wall cycle and its amplitude sensitivity to the superposed structures are similar to that of a canonical smooth-wall flow. These results indicate that the rough-wall structures above the internal layer interact with the near-wall cycle in a similar manner as the increasingly energetic structures in a high-Reynolds number smooth-wall boundary layer. @en

The evolution of turbulent boundary layers downstream of a rough-to-smooth transition is investigated at a range of Reynolds numbers. Measurements are performed at friction Reynolds numbers of 4100, 7100, 14000 and 21000 using hotwire anemometry. The wall-shear stress on the smooth surface in each case is measured directly using oil film interferometry. The growth of the internal layer is studied, and a full recovery of all energetic scales in the energy spectrum of the streamwise velocity fluctuations is observed at 80 boundary layer thicknesses downstream of the roughness transition. A comparison of recovery lengths required for various flow statistics (skin-friction coefficient and energy spectrum) is also presented.@en

The evolution of turbulent boundary layers downstream of a rough-to-smooth transition is investigated at a range of Reynolds numbers. Measurements are performed at friction Reynolds numbers of 4100, 7100, 14000 and 21000 using hotwire anemometry. The wall-shear stress on the smooth surface in each case is measured directly using oil film interferometry. The growth of the internal layer is studied, and a full recovery of all energetic scales in the energy spectrum of the streamwise velocity fluctuations is observed at 80 boundary layer thicknesses downstream of the roughness transition. A comparison of recovery lengths required for various flow statistics (skin-friction coefficient and energy spectrum) is also presented.@en