A large number of bridges in the Netherlands have transversely post tensioned deck slabs cast in-situ between flanges of precast girders and were found to be critical in shear when evaluated by Eurocode 2. To investigate the bearing (punching shear) capacity of such bridges, a 1:2 scale bridge model was constructed in the laboratory and static tests were performed by varying the transverse prestressing level (TPL). A 3D solid, 1:2 scale model of the real bridge, similar to the experimental model, was developed in the finite element software DIANA and several nonlinear analyses were carried out. It was observed that the experimental and numerical ultimate load carrying capacity was much higher than predicted by the governing codes due to lack of consideration of compressive membrane action (CMA). In order to incorporate CMA in the Model Code 2010 (fib 2012) punching shear provisions for prestressed slabs, numerical and theoretical approaches were combined. As a result, sufficient factor of safety was observed when the real bridge design capacity was compared with the design wheel load of Eurocode 1. It was concluded that the existing bridges still had sufficient residual bearing capacity with no problems of serviceability and structural safety.@en

It is widely known that as the structure of the size increases, its nominal strength decreases. In this paper, the effect of size on punching shear has been quantified for transversely post-Tensioned deck slabs cast between flanges of precast concrete girders. A 1:2 scaled model of the bridge was constructed in the laboratory, and experimental and numerical analyses were carried out. However, in order to apply these results on a real bridge, simply using the geometrical scale factors is not sufficient and a structural size effect has to be taken into account. Since a full-scale experimental study was not possible due to the costs involved, a numerical approach using finite element analysis software package TNO DIANA was used to model both the prototype and the real bridge, and a comparison was made to estimate the effect of size on the bearing capacity. It was found that increasing the transverse prestressing level had a positive effect on the punching shear strength of the deck slab. Furthermore, a lower size effect was observed with higher transverse prestressing levels. It is concluded that if a suitable size factor is used, either numerical or small-scale experimental studies can be reasonably used to investigate existing structures.@en

Most of the Dutch bridges were built around middle of the last century and it is vital for designers to find out if these bridges can still be considered safe for the traffic of modern times. The capacity in shear is especially critical as it was not considered in design recommendations before 1976. Therefore, experiments on a 1:2 scale model of a transversely prestressed concrete bridge deck cast between concrete girders were carried out to investigate the bearing (punching shear) capacity. The scale was selected based on the space available in the laboratory and the expected failure loads that would have to be applied. Also, a three-dimensional, solid, nonlinear finite element model was developed in the Finite Element Analysis software package TNO DIANA to study the structural behavior of deck slabs and is the focus of this paper. The results of the experimental and numerical analyses leads to the conclusion that existing bridges still have significant residual strength due to the presence of transverse prestressing and the membrane forces, and nonlinear finite element models can predict the load carrying capacity quite accurately.@en

Most of the Dutch bridges were built around middle of the last century and it is vital for designers to find out if these bridges can still be considered safe for the traffic of modern times. The capacity in shear is especially critical as it was not considered in design recommendations before 1976. Therefore, experiments on a 1:2 scale model of a transversely prestressed concrete bridge deck cast between concrete girders were carried out to investigate the bearing (punching shear) capacity. The scale was selected based on the space available in the laboratory and the expected failure loads that would have to be applied. Also, a three-dimensional, solid, nonlinear finite element model was developed in the Finite Element Analysis software package TNO DIANA to study the structural behavior of deck slabs and is the focus of this paper. The results of the experimental and numerical analyses leads to the conclusion that existing bridges still have significant residual strength due to the presence of transverse prestressing and the membrane forces, and nonlinear finite element models can predict the load carrying capacity quite accurately.@en

Most of the Dutch bridges were built around middle of the last century and it is vital for designers to find out if these bridges can still be considered safe for the traffic of modern times. The capacity in shear is especially critical as it was not considered in design recommendations before 1976. Therefore, experiments on a 1:2 scale model of a transversely prestressed concrete bridge deck cast between concrete girders were carried out to investigate the bearing (punching shear) capacity. The scale was selected based on the space available in the laboratory and the expected failure loads that would have to be applied. Also, a three-dimensional, solid, nonlinear finite element model was developed in the Finite Element Analysis software package TNO DIANA to study the structural behavior of deck slabs and is the focus of this paper. The results of the experimental and numerical analyses leads to the conclusion that existing bridges still have significant residual strength due to the presence of transverse prestressing and the membrane forces, and nonlinear finite element models can predict the load carrying capacity quite accurately.@en

Most of the Dutch bridges were built around middle of the last century and it is vital for designers to find out if these bridges can still be considered safe for the traffic of modern times. The capacity in shear is especially critical as it was not considered in design recommendations before 1976. Therefore, experiments on a 1:2 scale model of a transversely prestressed concrete bridge deck cast between concrete girders were carried out to investigate the bearing (punching shear) capacity. The scale was selected based on the space available in the laboratory and the expected failure loads that would have to be applied. Also, a three-dimensional, solid, nonlinear finite element model was developed in the Finite Element Analysis software package TNO DIANA to study the structural behavior of deck slabs and is the focus of this paper. The results of the experimental and numerical analyses leads to the conclusion that existing bridges still have significant residual strength due to the presence of transverse prestressing and the membrane forces, and nonlinear finite element models can predict the load carrying capacity quite accurately.@en

The Netherlands has a large number of thin, transversely prestressed concrete bridge decks, cast in-situ between flanges of prestressed concrete girders dating back to the 1960s and 1970s. These bridges are critical in shear when analyzed using EN 1992-1-1:2005; however, in reality, they show no significant signs of distress, possibly because of residual bearing (punching shear) capacity arising from compressive membrane action. Since these bridges are old, it is an astute approach to check whether they can be used for a few more decades, provided they are safe and reliable against modern traffic loads. The results could then be applied to a wider range of structures, especially in developing countries facing economic constraints. A prototype bridge was selected and experimental, numerical and theoretical approaches were used to investigate its bearing capacity. Respective coefficients of variation of 11% and 9% were obtained when the experimental and the finite element analysis punching loads were compared with the theoretical results. This led to the conclusion that the existing transversely prestressed concrete bridge decks still have sufficient bearing capacity and considerable cost savings can be made if compressive membrane action is considered in the analysis.@en

The Netherlands has a large number of thin, transversely prestressed concrete bridge decks, cast in-situ between flanges of prestressed concrete girders dating back to the 1960s and 1970s. These bridges are critical in shear when analyzed using EN 1992-1-1:2005; however, in reality, they show no significant signs of distress, possibly because of residual bearing (punching shear) capacity arising from compressive membrane action. Since these bridges are old, it is an astute approach to check whether they can be used for a few more decades, provided they are safe and reliable against modern traffic loads. The results could then be applied to a wider range of structures, especially in developing countries facing economic constraints. A prototype bridge was selected and experimental, numerical and theoretical approaches were used to investigate its bearing capacity. Respective coefficients of variation of 11% and 9% were obtained when the experimental and the finite element analysis punching loads were compared with the theoretical results. This led to the conclusion that the existing transversely prestressed concrete bridge decks still have sufficient bearing capacity and considerable cost savings can be made if compressive membrane action is considered in the analysis.@en

The Netherlands has a large number of thin, transversely prestressed concrete bridge decks, cast in-situ between flanges of prestressed concrete girders dating back to the 1960s and 1970s. These bridges are critical in shear when analyzed using EN 1992-1-1:2005; however, in reality, they show no significant signs of distress, possibly because of residual bearing (punching shear) capacity arising from compressive membrane action. Since these bridges are old, it is an astute approach to check whether they can be used for a few more decades, provided they are safe and reliable against modern traffic loads. The results could then be applied to a wider range of structures, especially in developing countries facing economic constraints. A prototype bridge was selected and experimental, numerical and theoretical approaches were used to investigate its bearing capacity. Respective coefficients of variation of 11% and 9% were obtained when the experimental and the finite element analysis punching loads were compared with the theoretical results. This led to the conclusion that the existing transversely prestressed concrete bridge decks still have sufficient bearing capacity and considerable cost savings can be made if compressive membrane action is considered in the analysis.@en

The Netherlands has a large number of thin, transversely prestressed concrete bridge decks, cast in-situ between flanges of prestressed concrete girders dating back to the 1960s and 1970s. These bridges are critical in shear when analyzed using EN 1992-1-1:2005; however, in reality, they show no significant signs of distress, possibly because of residual bearing (punching shear) capacity arising from compressive membrane action. Since these bridges are old, it is an astute approach to check whether they can be used for a few more decades, provided they are safe and reliable against modern traffic loads. The results could then be applied to a wider range of structures, especially in developing countries facing economic constraints. A prototype bridge was selected and experimental, numerical and theoretical approaches were used to investigate its bearing capacity. Respective coefficients of variation of 11% and 9% were obtained when the experimental and the finite element analysis punching loads were compared with the theoretical results. This led to the conclusion that the existing transversely prestressed concrete bridge decks still have sufficient bearing capacity and considerable cost savings can be made if compressive membrane action is considered in the analysis.@en