Objectives To evaluate how separate and combined climatic parameters affect peak core temperature during exercise in the heat using computer simulations fed with individual data. Methods The impact of eight environmental conditions on rectal temperature (T re) was determined for exercise under heat stress using the Fiala-thermal-Physiology-and-Comfort simulation model. Variations in ambient temperature (T a ±6°C), relative humidity (RH±15%) and solar radiation (SR+921 W/m 2) were assessed in isolation and combination (worst-case/best-case scenarios) and compared with baseline (T a 32°C, RH 75%, SR 0 W/m 2). The simulation model was fed with personal, anthropometric and individual exercise characteristics. Results 54 athletes exercised for 46±10 min at baseline conditions and achieved a peak core temperature of 38.9±0.5°C. Simulations at a higher T a (38°C) and SR (921 W/m 2) resulted in a higher peak T re compared with baseline (+0.6±0.3°C and +0.5±0.2°C, respectively), whereas a higher RH (90%) hardly affected peak T re (+0.1±0.1°C). A lower T a (26°C) and RH (60%) reduced peak T re by-0.4±0.2°C and a minor-0.1±0.1°C, respectively. The worst-case simulation yielded a 1.5±0.4°C higher T re than baseline and 2.0±0.7°C higher than the best-case condition. Conclusion Combined unfavourable climatic conditions produce a greater increase in peak core temperature than the sum of its parts in elite athletes exercising in the heat.

@en

Cooling vests containing phase change materials (PCMs) are used to reduce heat stress in hot environments and maintain the body core temperature within a safe range. The performance of such cooling vests depends in a complicated way on the PCM material and mass, the insulation value of the clothing layers and heat loss to the environment. Conventionally, these performance parameters are evaluated experimentally or using a numerical model, both of which do need a certain
amount of evaluation time. The objective of this paper is to develop a transient heat transfer model which includes metabolic heat production in the human body, as well as clothing and PCM layers and radiation to the environment but which is presented as a series of closed-form equations that can be evaluated without the need of a numerical solver. We present solutions for the body and PCM temperature as well as for the heat flux, cooling power and cooling duration. The model equations are validated by comparing them with experiments of ice PCM packs on a hotplate, as well as with published experimental and numerical data for the core temperature, heat flux and percentage of environmental heat loss using a Glauber salt type of PCM. Both the hotplate experiments and the model predictions show that the cooling power during PCM melting drops from about 70 to 32 W for increasing insulation layer thicknesses. In addition, the model is seen to compare well with experimental and simulation data in the literature. In a parametric study, we show how the equations can be used to evaluate the effects of PCM melting temperature and PCM thickness on cooling performance. The paper, therefore, can be considered as a practical means to help select the best cooling vest configuration for workers in a hot and humid environment.@en

Eleven phase change materials (PCMs) for cooling humans in heat-stressed conditions were evaluated for their cooling characteristics. Effects of packaging material and segmentation were also investigated. Sample packs with a different type PCM (water- and oil-based PCMs, cooling gels, inorganic salts) or different packaging (aluminum, TPU, TPU + neoprene) were investigated on a hotplate. Cooling capacity, duration, and power were determined. Secondly, a PCM pack with hexagon compartments was compared to an unsegmented version with similar content. Cooling power decreased whereas cooling duration increased with increasing melting temperature. The water-based PCMs showed a >2x higher cooling power than other PCMs, but were relatively short-lived. The flexible gels and salts did not demonstrate a phase change plateau in cooling power, compromising their cooling potential. Using a TPU or aluminum packaging was indifferent. Adding neoprene considerably extended cooling duration, while decreasing power. Segmentation has practical benefits, but substantially lowered contact area and therefore cooling power.

@en

The environmental conditions during the Tokyo Olympic and Paralympic Games are expected to be challenging, which increases the risk for participating athletes to develop heat-related illnesses and experience performance loss. To allow safe and optimal exercise performance of Dutch elite athletes, the Thermo Tokyo study aimed to determine thermoregulatory responses and performance loss among elite athletes during exercise in the heat, and to identify personal, sports-related, and environmental factors that contribute to the magnitude of these outcomes. For this purpose, Dutch Olympic and Paralympic athletes performed two personalized incremental exercise tests in simulated control (15°C, relative humidity (RH) 50%) and Tokyo (32°C, RH 75%) conditions, during which exercise performance and (thermo)physiological parameters were obtained. Thereafter, athletes were invited for an additional visit to conduct anthropometric, dual-energy X-ray absorptiometry (DXA), and 3D scan measurements. Collected data also served as input for a thermophysiological computer simulation model to estimate the impact of a wider range of environmental conditions on thermoregulatory responses. Findings of this study can be used to inform elite athletes and their coaches on how heat impacts their individual (thermo)physiological responses and, based on these data, advise which personalized countermeasures (i.e. heat acclimation, cooling interventions, rehydration plan) can be taken to allow safe and maximal performance in the challenging environmental conditions of the Tokyo 2020 Olympic and Paralympic Games.

@en

Prolonged exposure to solar radiation can cause considerable heat stress. The application of reflective materials in garments or sunscreens is generally considered as an appropriate protective strategy. In this study, we aimed to compare a range of reflective and control fabrics on their ability to reduce the thermal impact of solar radiation. We evaluated 16 reflective and 5 control fabrics, varying in applicability for garments and/or sunscreens. Transmission of ultraviolet, visible light and infrared radiation was studied using artificial solar light. Thermal impact reduction was first studied using artificial infrared light and secondly using natural sunlight, measuring temperature right at the back and 10 cm behind the fabric after a 10-minute exposure. Most samples showed comparably low radiation transmission (<10%). However, substantially higher transmission was observed in perforated and mesh-like reflective fabrics, as well as light-colored controls and coldblack® treated fabric. This resulted in larger temperature increases at 10 cm behind the fabric (+1-4°C in sunlight). Contact temperature at the back of the black fabrics ended up higher than at the back of the reflective and white control fabrics (T: 5-10°C in sunlight), the latter two showing minor mutual differences (T<3°C). In conclusion, the reflective fabrics (excluding perforated, mesh and coldblack®) showed minor mutual differences, lower heat absorption than the black control fabrics and lower heat transmission than the white ones. The results suggest that reflective or white fabrics are preferable for most garment applications, while reflective or possibly black fabrics are preferable for sunscreen applications.@en

Phase change material ( is regularly used in cooling garment, but the assessment of its effective cooling power in practice remains a challenge This study aimed to explore this assessment for two PCMs when applied in a cooling vest during moderate exercise Subsequently, thermal simulation was used to estimate its effect on body temperatures@en