Up to now, not much is known about how humans control bicycles, especially when subject to large perturbations. In order to learn more about the extent to which these perturbations can be handled, a new experimental setup is required, which can deliver large perturbations to cyclists and bring them to fall. This thesis describes the detailed design and evaluation of such a setup. Several requirements are formulated regarding different experiment aspects that the setup must adhere to. The proposed design consists of a treadmill on which a subject rides a bicycle. Ropes are guided from the ends of the bicycle’s handlebar toward the front and back of the setup, where they are attached to four motor units of a robotic rope-pulling system. Based on a feed-forward conversion added with PI force feedback control, a shared controller commands the motors to maintain a tracking force or perturb the cyclist by applying a net torque on the handlebar for a short time. An active safety harness is the main feature that prevents the subject from harm. Meanwhile, motion capture recordings of strategically placed passive markers and data from inertial measurement units on the bicycle are collected. With appropriate processing, the angles and angular velocities that describe the dynamics and control of the bicycle-rider system can be obtained from these measurements. The force data is also collected, by the controller. Interesting results that can be obtained with this setup include the probabilities to fall after perturbations of variable forces and the data required to evaluate the equations of motions of the bicycle-rider system during and shortly after a perturbation. This can be used to provide a baseline against which future bicycles can be compared and it is useful for validating rider models. The experiment shows consistent performance and generates high quality measurements. Neither the 12 pilot participants nor the 26 subjects who participated in follow-up experiments encountered any safety issues. The experiment could even be improved by resolving issues regarding the motor behaviour and CPU overloads. The workload of the experiment operators could be decreased if intervention of the safety harness was trained on cycling and coupled to deactivation of the treadmill. A next step would be to automate the data processing by developing a classifier that distinguishes recoveries from falls.

Part of the goal of Europe’s Strategy Vision Zero is to eliminate all severe cycling accidents in Europe by 2030. The majority of cycling accidents are single vehicle accidents; this term indicates the absence of collisions with other road participants and implies a fall of the cyclist. Research has shown that mainly elderly cyclists are victim to those accidents. An untested hypothesis is that their slowed motor responses are one of the main reasons behind this. This study aims to address this hypothesis by studying the influence of neural time delay on the lateral stability of bicycle-rider systems. In this study, the slowed motor responses are represented by single neural time delay values. The influence is quantified by the sizes of the identified basins of attraction of stability (BoA). The BoA contains the set of finite lateral disturbances for which stability is
retained and is acquired via numerical integration. Binary threshold criteria are used to determine the stability of the solution. The bicycle-rider system consists of two components: a bicycle model and a rider model. The bicycle is modelled using the Whipple(-Carvallo) bicycle model with the set of non-linear equations derived by Basu-Mandal [2]. The rider is modelled using an implicit experimentally validated model from literature [31]. This model consists of a PID controller with full state feedback, neuro-muscular dynamics and, in this study, is extended to include nonzero time delay. The neural time delay value of a young cyclist has been based on literature [4]. The value is doubled to model an older cyclist. The control strategy of the young cyclist is identified using system identification techniques. The basins of the young and old cyclist are compared to study the detrimental effect of time delay on lateral stability in cycling. It declined over 80% when the time delay was doubled. The human’s ability to adapt its control to circumstances has been considered by repeating the control identification process for the rider which suffers from double the time delay. With respect to the young cyclist, a decline of over 50% was observed. Therefore, the results strongly support the hypothesis. Further research should focus on increasing complexity of the rider model to include preview and prediction. In this way, the influence of slowed motor responses can be mapped more clearly.
A secondary objective of this thesis is the preliminary development of a steer assist control model to aid the elderly cyclist balance during cycling. This development builds further on a simple control model from literature [29] which uses roll angle feedback. As a result, a nonlinear velocity dependent roll rate feedback control law was developed. This control law yields a constant basin height over the commonly used velocity range of cyclists. This height indicates the maximum allowable steer rate perturbations the bicycle-steer assist system could handle and is approximately the same height as what was identified for
a young cyclist. Future research is required for improving the steer assist. This means adding maximum allowable control torque, sensorial time delays and trajectory tracking