BM
B.D. Meekes
info
Please Note
<p>This page displays the records of the person named above and is not linked to a unique person identifier. This record may need to be merged to a profile.</p>
2 records found
1
This work proposes an energy harvesting DC-DC converter that is able to efficiently process a wide input power range from 25 mW up to 250 mW, to charge a storage device used in Internet-of-Things (IoT) applications. An interleaved boost-converter topology with two inductors is used to divide the high currents over the two branches, in order to reduce the conduction losses in the MOSFET power switches at high input power.
A Maximum Power Point Tracking (MPPT) strategy is employed to find the optimal matching between the harvesting sensor, which in this case is a solar cell, and the input of the converter. The Maximum Power Point (MPP) is found by measuring the output current of the converter, decreasing the duty cycle of the switching power MOSFETs, and again measuring the output current to check if it increases. This process is repeated until the output current no longer increases, which is where the MPP will be. The duty-cycle pulses that control the power switches are generated by comparing a reference voltage representing the duty cycle with two sawtooth waves with a phase difference of 180 degrees generated on-chip.
Usually, for converters that handle large currents, large power switches are required to keep the on-resistance of the switches minimal such that the conduction losses do not dominate. Since the converter also needs to be able to efficiently convert smaller powers, the size of the power switches is made configurable. This is necessary since otherwise the gate-charge losses will become dominant. The total size of the segmented power switches are controlled digitally by a logic unit that calculates the expected input current using 2-bit representations of the measured output current and the two most significant bits of the 5-bit representation for the duty cycle set by the MPPT.
Schematic simulation results show a conversion efficiency of up to 92%. The proposed system is designed and simulated using 180 nm TSMC CMOS technology. The chip covers a total silicon area of 2.20 mm2, with an active area of 1.12 mm2. ...
A Maximum Power Point Tracking (MPPT) strategy is employed to find the optimal matching between the harvesting sensor, which in this case is a solar cell, and the input of the converter. The Maximum Power Point (MPP) is found by measuring the output current of the converter, decreasing the duty cycle of the switching power MOSFETs, and again measuring the output current to check if it increases. This process is repeated until the output current no longer increases, which is where the MPP will be. The duty-cycle pulses that control the power switches are generated by comparing a reference voltage representing the duty cycle with two sawtooth waves with a phase difference of 180 degrees generated on-chip.
Usually, for converters that handle large currents, large power switches are required to keep the on-resistance of the switches minimal such that the conduction losses do not dominate. Since the converter also needs to be able to efficiently convert smaller powers, the size of the power switches is made configurable. This is necessary since otherwise the gate-charge losses will become dominant. The total size of the segmented power switches are controlled digitally by a logic unit that calculates the expected input current using 2-bit representations of the measured output current and the two most significant bits of the 5-bit representation for the duty cycle set by the MPPT.
Schematic simulation results show a conversion efficiency of up to 92%. The proposed system is designed and simulated using 180 nm TSMC CMOS technology. The chip covers a total silicon area of 2.20 mm2, with an active area of 1.12 mm2. ...
This work proposes an energy harvesting DC-DC converter that is able to efficiently process a wide input power range from 25 mW up to 250 mW, to charge a storage device used in Internet-of-Things (IoT) applications. An interleaved boost-converter topology with two inductors is used to divide the high currents over the two branches, in order to reduce the conduction losses in the MOSFET power switches at high input power.
A Maximum Power Point Tracking (MPPT) strategy is employed to find the optimal matching between the harvesting sensor, which in this case is a solar cell, and the input of the converter. The Maximum Power Point (MPP) is found by measuring the output current of the converter, decreasing the duty cycle of the switching power MOSFETs, and again measuring the output current to check if it increases. This process is repeated until the output current no longer increases, which is where the MPP will be. The duty-cycle pulses that control the power switches are generated by comparing a reference voltage representing the duty cycle with two sawtooth waves with a phase difference of 180 degrees generated on-chip.
Usually, for converters that handle large currents, large power switches are required to keep the on-resistance of the switches minimal such that the conduction losses do not dominate. Since the converter also needs to be able to efficiently convert smaller powers, the size of the power switches is made configurable. This is necessary since otherwise the gate-charge losses will become dominant. The total size of the segmented power switches are controlled digitally by a logic unit that calculates the expected input current using 2-bit representations of the measured output current and the two most significant bits of the 5-bit representation for the duty cycle set by the MPPT.
Schematic simulation results show a conversion efficiency of up to 92%. The proposed system is designed and simulated using 180 nm TSMC CMOS technology. The chip covers a total silicon area of 2.20 mm2, with an active area of 1.12 mm2.
A Maximum Power Point Tracking (MPPT) strategy is employed to find the optimal matching between the harvesting sensor, which in this case is a solar cell, and the input of the converter. The Maximum Power Point (MPP) is found by measuring the output current of the converter, decreasing the duty cycle of the switching power MOSFETs, and again measuring the output current to check if it increases. This process is repeated until the output current no longer increases, which is where the MPP will be. The duty-cycle pulses that control the power switches are generated by comparing a reference voltage representing the duty cycle with two sawtooth waves with a phase difference of 180 degrees generated on-chip.
Usually, for converters that handle large currents, large power switches are required to keep the on-resistance of the switches minimal such that the conduction losses do not dominate. Since the converter also needs to be able to efficiently convert smaller powers, the size of the power switches is made configurable. This is necessary since otherwise the gate-charge losses will become dominant. The total size of the segmented power switches are controlled digitally by a logic unit that calculates the expected input current using 2-bit representations of the measured output current and the two most significant bits of the 5-bit representation for the duty cycle set by the MPPT.
Schematic simulation results show a conversion efficiency of up to 92%. The proposed system is designed and simulated using 180 nm TSMC CMOS technology. The chip covers a total silicon area of 2.20 mm2, with an active area of 1.12 mm2.
Bachelor thesis
(2018)
-
Bauke Meekes, Victor Waegenaere, Ger de Graaf, Marjan Popov, Faruk Uysal, John Schmitz
This report discusses one part of a project consisting of three parts. The goal of the project is to design a battery less sensor powered by RF energy fields present in an office environment. The sensor is able to measure the temperature and is able to communicate wirelessly using a low power communication protocol. In this project the use case of a building is explored. This thesis treats the RF energy harvesting part, which scavenges the RF power out of the ether and delivers it to the rectifier to convert and store the energy. First the spectrum has been analyzed to determine the most suitable frequency band. An antenna has been designed to harvest as much power at the chosen frequency. To make the power transfer from the antenna to the rectifier as efficient as possible, a matching circuit for matching the impedances is implemented. In this report, a Planar Inverted-F Antenna is designed to meet all the given requirements.
...
This report discusses one part of a project consisting of three parts. The goal of the project is to design a battery less sensor powered by RF energy fields present in an office environment. The sensor is able to measure the temperature and is able to communicate wirelessly using a low power communication protocol. In this project the use case of a building is explored. This thesis treats the RF energy harvesting part, which scavenges the RF power out of the ether and delivers it to the rectifier to convert and store the energy. First the spectrum has been analyzed to determine the most suitable frequency band. An antenna has been designed to harvest as much power at the chosen frequency. To make the power transfer from the antenna to the rectifier as efficient as possible, a matching circuit for matching the impedances is implemented. In this report, a Planar Inverted-F Antenna is designed to meet all the given requirements.