The atomic-level study of point defect evolution in nuclear graphite is essential for a deep understanding of irradiation-induced property changes. The evolution of helium ion irradiation-induced point defects and helium retention in nuclear graphite ETU-10 and ETU-15 were studied by positron annihilation Doppler broadening (PADB) experiments and thermal desorption spectroscopy (TDS) measurements. The graphite samples were implanted with 10¹⁵, 10^16_, and 10¹⁷ cm⁻² of 200 keV He⁺ at operation temperatures below 373 K. Frenkel pairs were created during ion irradiation and they annihilated during annealing. Three stages of interstitial-monovacancy annihilation are suggested. At low temperatures, the initial annihilation would be refined only to the recombination of intimate metastable Frenkel pairs. When temperature increases, the annihilation would expand to a larger extent that isolate interstitials and vacancies annihilate with each other. In the case of high doses irradiation, vacancy clusters form at elevated temperatures. The retention and release of helium is tightly related to the evolution of the defects, especially the vacancies. The small over-pressured He-V clusters (He_nV) are thought to be the most possible form of helium retention under irradiation.

The reactor pressure vessel (RPV) is the key component in the nuclear power plant, which is considered irreplaceable and can be the life-limiting feature of the operation of nuclear power plant if its mechanical properties degrade sufficiently. High temperature gas-cooled reactor (HTGR) has perfect inherent safety, which is intended to be one of the fourth generation advanced nuclear reactors. However, HTGR has different service temperature with pressurized water reactor (PWR), that the service temperature of HTGR is 250℃ and that of PWR is 290℃. So the irradiation behaviour of RPV in HTGR is expected to be investigated. In this wok, 3 MeV Fe-ion irradiation was performed on Chinese A508-3 reactor pressure vessel steel which is employed by high-temperature gas-cooled reactors and pure Fe under room temperature (about 25℃) and high temperature (250℃). The ion doses were 0.1, 0.5 and 1.0 dpa for both room temperature irradiation and high temperature irradiation. SRIM modeling was performed before irradiation experiments to guide the experimental details. Positron annihilation Doppler broadening (PADB) spectroscopy experiments and nano-indentation tests (to study embrittlement behavior) were conducted for characterization. It is found that after both room temperature irradiation and high temperature irradiation, the densities of defects in the reactor pressure vessel steel and pure Fe increase, and the type of defects could be vacancy-type and solute cluster type from PADB results. The vacancy-type defect density under high temperature irradiation is lower than that under room temperature irradiation. That is because high temperature can recover the defects formed during irradiation. The hardness test results show that for both the reactor pressure vessel steel and pure Fe, the irradiation hardening increases with increasing dose. Compared to room temperature irradiation, high temperature irradiation can produce more solute clusters and fewer vacancy-type defects in the reactor pressure vessel steel. So the irradiation hardening of the reactor pressure vessel steel might be caused mainly by the formation of solute clusters.

Electrical mobility demands an increase of battery energy density beyond current lithium-ion technology. A crucial bottleneck is the development of safe and reversible lithium-metal anodes, which is challenged by short circuits caused by lithium-metal dendrites and a short cycle life owing to the reactivity with electrolytes. The evolution of the lithium-metal-film morphology is relatively poorly understood because it is difficult to monitor lithium, in particular during battery operation. Here we employ operando neutron depth profiling as a noninvasive and versatile technique, complementary to microscopic techniques, providing the spatial distribution/density of lithium during plating and stripping. The evolution of the lithium-metal-density-profile is shown to depend on the current density, electrolyte composition and cycling history, and allows monitoring the amount and distribution of inactive lithium over cycling. A small amount of reversible lithium uptake in the copper current collector during plating and stripping is revealed, providing insights towards improved lithium-metal anodes.

The original HTML version of this Article omitted to list Zhengcao Li as a corresponding author. Correspondingly, the original PDF version of this Article incorrectly stated that ‘Correspondence and requests for materials should be addressed to M.W. (email: m.wagemaker@tudelft.nl)’, instead of the correct ‘Correspondence and requests for materials should be addressed to Z.L. (email: zcli@tsinghua.edu.cn) or to M.W. (email: m.wagemaker@tudelft.nl)’. This has been corrected in both the PDF and HTML versions of the Article.

The irradiation and annealing behavior of Chinese A508-3 reactor pressure vessel (RPV) steel (0.04 wt% Cu) after 3 MeV Fe-ion irradiation ranging from 0.1 to 20 dpa at room temperature (called RTRPV) and high temperature (250 °C, called HTRPV) was studied by positron annihilation Doppler broadening (PADB) spectroscopy and nano-indentation hardness. PADB showed that the density of vacancy-type defects was higher for low-temperature irradiations. The higher hardness was found after high-temperature irradiation because of the formation of solute clusters during irradiation. Positron annihilation measurements revealed the interaction and clustering of vacancies with solute clusters which were introduced by Fe-ion irradiation. For both RTRPVs and HTRPVs, the positron defect parameter and positron diffusion length showed the recovery of the irradiation-induced defects. Total recovery was observed after annealing at 450 °C.