Surfactant losses by adsorption to rock surfaces make surfactant-based enhanced oil recovery economically less feasible. We investigated polyacrylate (PA) as a sacrificial agent in the reduction of anionic surfactant adsorption with focus on calcite surfaces by using quartz crystal microbalance with dissipation monitoring. It was found that the adsorption of the anionic surfactant alcohol alkoxy sulfate (AAS) followed a Langmuir adsorption isotherm, and the adsorbed amount reached saturation above its critical micellar concentration. Adsorption of PA was a much slower process compared to AAS adsorption. Increasing the calcium ion concentration also increased the amount of AAS adsorbed as well as the mass increase rate of PA adsorption. Experimental results combined with density functional theory calculations indicated that calcium cation bridging was important for anionic surfactant AAS and PA adsorption to calcite surfaces. To effectively reduce the amount of surfactant adsorption, it was needed to preflush with PA, rather than by a simultaneous injection. Preflushing with 30 ppm of PA gave a reduction of AAS adsorption of 30% under high salinity (HS, 31,800 ppm) conditions, compared to 8% reduction under low salinity (LS, 3180 ppm) conditions. In the absence of PA, the amount of adsorbed AAS was reduced by already 50% upon changing from HS to LS conditions. Lower calcium ion concentrations, as under LS conditions, contributed to this observation. On different mineral surfaces, PA reduced the AAS adsorption in the order of alumina > calcite > silica. These results offer important insights into mitigating surfactant adsorption using PA polyelectrolyte as sacrificial agent and contribute to improved flooding strategies with reduced surfactant loss.

In view of enhanced oil recovery, the adsorption behavior of surfactants is usually monitored on smooth model rock surfaces using quartz crystal microbalance with dissipation (QCM-D). However, this is an impractical situation as the effect of the surface roughness of reservoir rocks and its role in surfactant adsorption processes are not yet completely understood. The coupling of electrochemical techniques and QCM-D in one analysis setup (EQCM-D) provides a new methodology to explore complex surfactant adsorption processes. In this work, a uniform, rough, and well-covered model CaCO3 surface was obtained on gold and platinum sensors to model carbonate rocks. This was achieved by the electrochemically formed hydroxide ions in the presence of bicarbonate and calcium ions, by which the controlled deposition of CaCO3 resulted in sensor surface coverages in the range 35-40%. Before using the deposited CaCO3 surfaces, the adsorption of anionic surfactant alcohol alkoxy sulfate (AAS) on a smooth commercially available CaCO3 surface was studied with varying CaCl2 concentrations. For the first time, the structure and characteristics of the formed AAS layer were quantitatively described, indicating the formation of an incomplete bilayer. Compared to the smooth CaCO3 surface, an increase in the frequency shift from 5 to 15 times was observed in sensors covered with rough CaCO3 deposit. This observation was primarily attributed to the rougher surfaces that possess more adsorption sites for AAS binding and also to the effect of liquid trapping, inducing additional frequency shifts. The obtained results show that surfactant adsorption on rough surfaces was vastly different from that on smooth surfaces, and they provide a better understanding of the adsorption behavior of surfactants to mineral surfaces.

Adsorption behavior of surfactants to rock surfaces is an important issue in oil recovery, especially in the process of surfactant flooding. The surfactant loss through adsorption to rock surfaces makes such process economically less feasible. Here, we investigated the adsorption behavior of anionic surfactants (alcohol alkoxy sulfate, AAS) onto silica with quartz crystal microbalance with dissipation monitoring. The results demonstrated that the surfactant adsorption followed the Langmuir adsorption isotherm. Up to solution pH 10, surfactant adsorption slightly increased with increasing pH. The higher pH leads to more anionic surface sites for binding with an anionic surfactant with the help of a calcium cation bridging. The amount of anionic surfactant binding also increases with increasing calcium ion concentration up to 50 mM. It was found that sodium ions were able to exchange calcium ions near the silica surface, which would reduce the affinity for surfactant adsorption. The effect of the polyanion polystyrene sulfonate (PSS) on the anionic AAS adsorption was investigated to learn the possible competitive adsorptions. Indeed, this was found. Upon addition of 50 ppm PSS to a 0.05 wt% AAS containing solution, the adsorption of AAS was reduced by about 85 %. The obtained results show the interplay of different interacting species affecting the overall degree of anionic surfactant adsorption to silica surfaces. Optimal tuning of the process conditions according to these results will contribute to a more efficient use of anionic surfactants in enhanced oil recovery.

To the best of our knowledge, for the first time MIL-53(Al) and NH ₂ -MIL-53(Al) modified α-alumina membranes are investigated for the adsorption of organic dyes from organic solvents. These new, modified membranes show excellent adsorption of high concentrations of Rose Bengal dye in methanol and isopropanol solutions.