Chemical loss such as surfactants and alkalis by adsorption to reservoir rock surface is an important issue in enhanced oil recovery (EOR). Here, we investigated the adsorption behaviors of anionic surfactants and alkalis on silica for the first time as a function of temperature using quartz crystal microbalance with dissipation (QCM-D). The results demonstrated that the temperature dependent critical micelle concentration of alcohol alkoxy sulfate (AAS) surfactant can be quantitatively described by the thermodynamics parameters of micellization, showing a mainly entropy-driven process. AAS adsorption was mediated under varying temperature conditions, by divalent cations for bridging effect, monovalent cations competitive for adsorption sites but not giving cation bridging, pH regulation of deprotonated sites of silica, presence of alkoxy groups in the surfactants, and synergistic effect of surfactant co-injection. The addition of organic alkalis can enhance the overall adsorption of the species with AAS, whereas inorganic alkali of Na2CO3 had capability of the sequestration of the divalent ions, whose addition would reduce AAS adsorption. The typical AAS adsorption indicated a non-rigid multilayer, estimated to have between 2 and 5 layers, with a likely compact bilayer followed by disorganized and unstable further layering. The new fundamental understanding about temperature effect on surfactants and alkalis adsorption contributes to optimizing the flooding conditions of chemicals and developing more efficient mitigation strategies.@en

Adsorption behavior of surfactants to rock surfaces is an important issue in oil recovery, especially in the process of surfactant flooding. The surfactant loss through adsorption to rock surfaces makes such process economically less feasible. Here, we investigated the adsorption behavior of anionic surfactants (alcohol alkoxy sulfate, AAS) onto silica with quartz crystal microbalance with dissipation monitoring. The results demonstrated that the surfactant adsorption followed the Langmuir adsorption isotherm. Up to solution pH 10, surfactant adsorption slightly increased with increasing pH. The higher pH leads to more anionic surface sites for binding with an anionic surfactant with the help of a calcium cation bridging. The amount of anionic surfactant binding also increases with increasing calcium ion concentration up to 50 mM. It was found that sodium ions were able to exchange calcium ions near the silica surface, which would reduce the affinity for surfactant adsorption. The effect of the polyanion polystyrene sulfonate (PSS) on the anionic AAS adsorption was investigated to learn the possible competitive adsorptions. Indeed, this was found. Upon addition of 50 ppm PSS to a 0.05 wt% AAS containing solution, the adsorption of AAS was reduced by about 85 %. The obtained results show the interplay of different interacting species affecting the overall degree of anionic surfactant adsorption to silica surfaces. Optimal tuning of the process conditions according to these results will contribute to a more efficient use of anionic surfactants in enhanced oil recovery.@en

Surfactants have the ability to mobilize residual oil trapped in pore spaces of matrix rocks by lowering the oil-water interfacial tension, resulting in a higher oil recovery. However, the loss of surfactants by adsorption onto the rock surface has become a major concern that reduces the efficiency of the surfactant flooding process. In this study, the adsorption behavior of an anionic surfactant to a clay mineral surface was investigated by quartz crystal microbalance with dissipation monitoring upon variations with different cation conditions. Through recording the change of frequency and dissipation of clay-modified sensors, it allows us to do a real-time quantitative analysis of the surfactant adsorption with nanogram sensitivity. The results revealed that the surfactant adsorption increased in a Ca2+-containing solution with increasing pH from 6 to 11, whereas from a Na+-containing solution, more adsorption occurred at acidic conditions. The adsorbed amount went through a maximum (∼200 mM) as a function of the Ca2+ concentration, and the Voigt model suggested that multilayer adsorption of surfactants could be as many as 4-6 monolayers. Using mixed cation (Ca2+ and Na+) solutions, the amount of adsorbed surfactant decreased linearly with decreasing fraction of CaCl2, but Na+ competed for about ∼30% adsorption sites. The importance of the presence of CaCl2 for the surfactant adsorption was stressed in high-salinity and low-salinity solutions in the presence and absence of Ca2+. Furthermore, increasing the temperature from 23 to 65 °C shows first a small increase of surfactant adsorption followed by a reduction of about 20%. The obtained results contribute to a better understanding of surfactant adsorption on clay surfaces and a guide to optimal flooding conditions with reduced surfactant loss.@en

The ability to study the adsorption behavior of surfactant species is of interest in the field of enhanced oil recovery (EOR), especially pertaining to alkaline surfactant flooding. In this work, a calcite model mineral surface was obtained by electrochemically assisted deposition. This was achieved via the nitrate and/or oxygen electroreduction reactions in the presence of bicarbonate and calcium ions, by which controlled deposition of calcium carbonate was effected on a quartz crystal microbalance sensor covered with an electroactive gold layer. In addition, the effect of pH and Ca 2+ concentration on the effective surface charge of the deposited calcite particles was mapped. Calcite-modified sensors were used in conjunction with a quartz crystal microbalance with dissipation monitoring to study the effect of Na + and Ca 2+ concentration on the adsorption behavior of an anionic alcohol alkoxy sulfate (AAS) surfactant. Adsorption of the surfactant remained indifferent to ionic concentrations around the isoelectric point of calcite. Still, electrostatics play an important role in this regard, and it is essential to decrease the Ca 2+ concentration sufficiently to minimize AAS adsorption. The results from this study show that a relatively simple method allows for the controlled deposition of a model rock surface, and there is ample opportunity to extend the work to other metal oxide surface types, including complex mixtures as can be obtained by co-deposition. Furthermore, the findings from these adsorption studies aid in the determination of optimal flooding parameters, with the aim to increase the efficiency and efficacy of EOR. @en