Controlled localization of platinum nanoparticles (Pt NPs) at a solid support assisted by a polarized liquid-liquid interface is reported. Electrocatalytic water oxidation resulted in local pH modulation followed by the directed self-assembly of a dibenzoyl-l-cystine hydrogelator forming a structured hydrogel retaining the shape of the Pt NP deposit.

The ability to study the adsorption behavior of surfactant species is of interest in the field of enhanced oil recovery (EOR), especially pertaining to alkaline surfactant flooding. In this work, a calcite model mineral surface was obtained by electrochemically assisted deposition. This was achieved via the nitrate and/or oxygen electroreduction reactions in the presence of bicarbonate and calcium ions, by which controlled deposition of calcium carbonate was effected on a quartz crystal microbalance sensor covered with an electroactive gold layer. In addition, the effect of pH and Ca ²⁺ concentration on the effective surface charge of the deposited calcite particles was mapped. Calcite-modified sensors were used in conjunction with a quartz crystal microbalance with dissipation monitoring to study the effect of Na ⁺ and Ca ²⁺ concentration on the adsorption behavior of an anionic alcohol alkoxy sulfate (AAS) surfactant. Adsorption of the surfactant remained indifferent to ionic concentrations around the isoelectric point of calcite. Still, electrostatics play an important role in this regard, and it is essential to decrease the Ca ²⁺ concentration sufficiently to minimize AAS adsorption. The results from this study show that a relatively simple method allows for the controlled deposition of a model rock surface, and there is ample opportunity to extend the work to other metal oxide surface types, including complex mixtures as can be obtained by co-deposition. Furthermore, the findings from these adsorption studies aid in the determination of optimal flooding parameters, with the aim to increase the efficiency and efficacy of EOR.

Capacitors made of interdigitated electrodes (IDEs) as a transducer platform for the sensing of volatile organic compounds (VOCs) have advantages due to their lower power operation and fabrication using standard micro-fabrication techniques. Integrating a micro-electromechanical system (MEMS), such as a microhotplate with IDE capacitor, further allows study of the temperature- dependent sensing response of VOCs. In this paper, the design, fabrication, and characterization of a low-power MEMS microhotplate with IDE capacitor to study the temperature-dependent sensing response to methanol using Zeolitic imidazolate framework (ZIF-8), a class of metal-organic framework (MOF), is presented. A Titanium nitride (TiN) microhotplate with aluminum IDEs suspended on a silicon nitride membrane is fabricated and characterized. The power consumption of the ZIF-8 MOF-coated device at an operating temperature of 50 ∘ C is 4.5 mW and at 200 ∘ C it is 26 mW. A calibration methodology for the effects of temperature of the isolation layer between the microhotplate electrodes and the capacitor IDEs is developed. The device coated with ZIF-8 MOF shows a response to methanol in the concentration range of 500 ppm to 7000 ppm. The detection limit of the sensor for methanol vapor at 20 ∘ C is 100 ppm. In situ study of sensing properties of ZIF-8 MOF to methanol in the temperature range from 20 ∘ C to 50 ∘ C using the integrated microhotplate and IDE capacitor is presented. The kinetics of temperature-dependent adsorption and desorption of methanol by ZIF-8 MOF are fitted with double-exponential models. With the increase in temperature from 20 ∘ C to 50 ∘ C, the response time for sensing of methanol vapor concentration of 5000 ppm decreases by 28%, whereas the recovery time decreases by 70%.

Silicon semiconductors with a thin surface layer of silica were first modified with polyelectrolytes (polyethyleneimine, polystyrene sulfonate and poly(allylamine)) via a facile layer-by-layer deposition approach. Subsequently, lipid vesicles were added to the preformed polymeric cushion, resulting in the adsorption of intact vesicles or fusion and lipid bilayer formation. To study involved interactions we employed optical reflectometry, electrochemical impedance spectroscopy and fluorescent recovery after photobleaching. Three phospholipids with different charge of polar head groups, i.e. 1,2-dioleoyl-sn-glycero-3-phosphocholine (DOPC), 1,2-dioleoyl-sn-glycero-3-phospho-L-serine (DOPS) and 1,2-dioleoyl-3-trimethylammonium-propane (DOTAP) were used to prepare vesicles with varying surface charge. We observed that only lipid vesicles composed from 1:1 (mole:mole) mixture of DOPC/DOPS have the ability to fuse onto an oppositely charged terminal layer of polyelectrolyte giving a lipid bilayer with a resistance of >100 kΩ. With optical reflectometry we found that the vesicle surface charge is directly related to the amount of mass adsorbed onto the surface. An interesting observation was that zwitterionic polar head groups of DOPC allow the adsorption on both positively and negatively charged surfaces. As found with fluorescent recovery after photobleaching, positively charged surface governed by the presence of poly(allylamine) as the terminal layer resulted in intact DOPC lipid vesicles adsorption whereas in the case of a negatively charged silica surface formation of lipid bilayers was observed, as expected from literature.