The Ultraviolet Imager (UVI) is one of the instruments of the ESA-CAS Solar wind Magnetosphere Ionosphere Link Explorer (SMILE) joint mission to image Earth's northern auroral regions over the 160-180 nm UV waveband with a 10° × 10° field of view. The UV light is guided to the detector with four thin film-coated mirrors that ensure most of the signal filtering, crucial to achieve a high out-of-band rejection and limit contributions from solar diffusion, dayglow and unwanted atomic spectral lines. In this paper, we present the design and performances of the spectrally selective reflective coating, which is based on an interferential MgF2/LaF3 multilayer stack deposited by ion-assisted electron-beam evaporation. Its peak reflectivity is above 85 % and with an adjustable central wavelength within 1 nm, whereas the out-of-band reflectivity between 120 nm and 155 nm and between 200 nm and 1100 nm remains below 6 % on average. The coating has been space qualified (thermal cycling under vacuum, radiations, UV exposure...) and shows stable performances in conditions representative of the instrument operation environment.

We describe the state of development of a white light interferometer to characterize the cryogenic mirrors for GW detector on operation. We include the first experimental results from the proof of concept of the metrology instrument. The instrument will characterize the topology as well as the vibration of the mirrors. This development takes place in the frame of the E-TEST project. E-TEST is one of the technology demonstrators for the future Einstein Telescope (ET). ET is dedicated to the measure and characterization of gravitational waves. The prototype built by E-TEST includes a large silicon mirror of 40 cm diameter suspended by innovative vibration isolation hanging modules. To reach the detection specification, the mirror is cooled down at cryogenic temperatures around 20 K. Nevertheless, even after the isolation, the mirror may not reach perfect stability once at cryogenic temperatures. Furthermore, the mirror may experience surface topology changes and wavefront deformation due to the extreme variations in temperature and gradient. With our metrology instrument, we can obtain on a single camera frame a set of interferogram maps of the area observed on the mirror at different optical path differences. To do this, we design an innovative phase mask for a white light low-coherence interferometer. In addition, we implement new algorithms for the white light interferogram analysis, avoiding the limitations of the conventional Phase Shifting Interferometry algorithms.

In this article, we propose a new solar concentrator based on spectral splitting of sunlight. Spectral splitting has the objective to collect different spectra onto spectrally adapted solar cells for a more efficient use of the Sun's spectrum. Its combination with solar concentration makes an alternative to classical technologies. The proposed concentrator is composed of a diffractive/refractive optical element that spectrally splits and focuses the light onto a waveguide. The light is then conducted by total internal reflection towards the two specific solar cells. The optical concept and optimization of each element is presented in this paper. An adaptation for dye sensitized solar cells is performed. A geometrical factor around 5× is reached. Finally, theoretical optical efficiency, the manufacturing process and experimental testing with a collimated Sun simulator are presented.

We present a new solar concentrator concept. This concept is based on spectral splitting. It implies reflective, refractive and diffractive elements that allow two spectrally differentiated beams to reach different and/or unmatched lattice solar cells. The aimed geometrical concentration factor is 5× and the theoretical optical efficiency of that concentrator concept reaches theoretically 82%. The following study will discuss the concept of such a solar concentrator. A practical application to dye sensitized solar cells is given. The manufacturing and design of the element is then exposed. Those elements have been tested in the laboratory. Good agreements with theoretical simulations are demonstrated.

A primary optics for solar concentrator made of an achromatic Fresnel doublet has been designed and manufactured. The achromatic Fresnel doublet combines the advantages of plastic lenses without being affected by chromatic aberrations. The performance has been determined experimentally using a homemade continuous solar simulator and compared to paraxial theory and ray-tracing simulations. Experimental results are in good agreement with theory and show that the achromatic Fresnel doublet is tolerant to manufacturing errors and uncertainty on the dispersion of the refractive index: the concentration factor remains above 1600× with an f-number of 2.

To combine achromatic system with cost-effective technology, we propose the use or hybride (refractive/diffractive) and refractive doublets Fresnel lenses. These two technologies have been compared experimentally from an optical point of view.

The linear chromatic aberration (LCA) of several combinations of polycarbonates (PCs) and poly (methyl methacrylates) (PMMAs) as singlet, hybrid (refractive/diffractive) lenses and doublets operating with wavelengths between 380 and 1600 nm – corresponding to a typical zone of interest of concentrated photovoltaics (CPV) – are compared. Those comparisons show that the maximum theoretical concentration factor for singlets is limited to about 1000 × at normal incidence and that hybrid lenses and refractive doublets present a smaller LCA increasing the concentration factor up to 5000 × and 2 × 10⁶ respectively. A new achromatization equation more useful than the Abbé equation is also presented. Finally we determined the ideal position of the focal point as a function of the LCA and the geometric concentration which maximizes the flux on the solar cell.

We propose a new family of achromatic phase shifters for infrared nulling interferometry. These key optical components can be seen as optimized Fresnel rhombs, using the total internal reflection phenomenon, modulated or not. The total internal reflection indeed comes with a phase shift between the polarization components of the incident light. We propose a solution to implement this vectorial phase shift between interferometer arms to provide the destructive interference process needed to disentangle highly contrasted objects from one another. We also show that, modulating the index transition at the total internal reflection interface allows compensating for the intrinsic material dispersion in order to make the subsequent phase shift achromatic over especially broad bands. The modulation can be induced by a thin film of a well-chosen material or a subwavelength grating whose structural parameters are thoroughly optimized. We present results from theoretical simulations together with preliminary fabrication outcomes and measurements for a prototype in Zinc Selenide.

Thermal infrared (IR) lenses require efficient anti-reflection coating. Moth-eye (or egg-box) 2D subwavelength gratings have demonstrated their ability to reach a very high transmission for a wide wavelength and angular range. The use in thermal IR is simplified by the lower resolution for lithographic technology, compared to visible waveband. However, deeper structures must be engraved and lithography must be adapted to IR materials. In order to be cost-effective, the patterning must be produced by replication techniques, such as embossing. Our laboratory is now experimenting hot embossing of moth-eye patterns in chalcogenide substrates. In this paper, theoretical analysis, micro-lithographic technology and manufacturing processes are detailed.

We propose a new family of achromatic phase shifters that uses the modulated total internal reflection (TIR) phenomenon. These components can be seen as enhanced Fresnel rhombs for infrared applications like nulling interferometry and polarimetry. The TIR phenomenon comes with a differential phase shift between the polarization components of the incident light. Modulating the index transition at the TIR interface allows compensating for the intrinsic material dispersion in order to make the subsequent phase shift achromatic over broad bands. The modulation can be induced by a thin film of a well-chosen medium or a subwavelength grating whose parameters are specially optimized. We present results from theoretical simulations together with preliminary fabrication outcomes.