JK
J.A. Keuning
info
Please Note
<p>This page displays the records of the person named above and is not linked to a unique person identifier. This record may need to be merged to a profile.</p>
2 records found
1
Keel-Rudder Interaction
A look into the wake of a sailing yacht
In the early 00 of this century, Keuning et al. (2007) looked into the hydrodynamic forces on the rudder and the influence of the hull and keel on these forces. Among others, they have assessed the lift and drag forces on the rudder. One of the outcomes of this study was an asymmetric lift curve; for negative rudder angles the rudder seems to stall at angles more than five degrees smaller than for the positive rudder angles.
The goal for this research is to find and clarify the physical phenomenon which induces the rudder to stall at smaller rudder angles when subjected to a negative rudder angle (during bearing away). The main question to be answered in this report is: What physical phenomenon is at the basis of the asymmetric stalling behaviour on the rudder of a sailing yacht?
Towing tank tests are used to validate the data from Keuning et al. (2007). After which RANS CFD simulations are conducted in NUMECA to compare the towing tank tests to and to visualise the wake of the yacht in attempt to clarify the phenomena found.
A number of conclusions were found in this study. Firstly, the results of the towing tank experiments showed similarities to the previous experiments by Keuning et al. (2007). Differences are found in stall angles for positive rudder angles. These differences raise questions on the correctness of either of the experiments.
Secondly, no reasonable explanation is found for the negative drag forces found in the towing tank experiments. It is expected that these originate from the set-up of the rudder.
Thirdly, the lift curve found in the experiments is confirmed by the CFD data for the test cases. The physical effect behind the early stall behaviour of the rudder is still unknown. It is indicated that a part of the decrease in stall angle, a couple of degrees, is caused by the influence of the keel, when the disturbance passes on the low pressure side of the rudder. The hull is responsible for the remaining decrease. The CFD data indicates an influence of the vorticity of the keel and the boundary of the hull to cause a disturbance on the rudder.
Further research in necessary to clarify the results found in this study.
...
The goal for this research is to find and clarify the physical phenomenon which induces the rudder to stall at smaller rudder angles when subjected to a negative rudder angle (during bearing away). The main question to be answered in this report is: What physical phenomenon is at the basis of the asymmetric stalling behaviour on the rudder of a sailing yacht?
Towing tank tests are used to validate the data from Keuning et al. (2007). After which RANS CFD simulations are conducted in NUMECA to compare the towing tank tests to and to visualise the wake of the yacht in attempt to clarify the phenomena found.
A number of conclusions were found in this study. Firstly, the results of the towing tank experiments showed similarities to the previous experiments by Keuning et al. (2007). Differences are found in stall angles for positive rudder angles. These differences raise questions on the correctness of either of the experiments.
Secondly, no reasonable explanation is found for the negative drag forces found in the towing tank experiments. It is expected that these originate from the set-up of the rudder.
Thirdly, the lift curve found in the experiments is confirmed by the CFD data for the test cases. The physical effect behind the early stall behaviour of the rudder is still unknown. It is indicated that a part of the decrease in stall angle, a couple of degrees, is caused by the influence of the keel, when the disturbance passes on the low pressure side of the rudder. The hull is responsible for the remaining decrease. The CFD data indicates an influence of the vorticity of the keel and the boundary of the hull to cause a disturbance on the rudder.
Further research in necessary to clarify the results found in this study.
...
In the early 00 of this century, Keuning et al. (2007) looked into the hydrodynamic forces on the rudder and the influence of the hull and keel on these forces. Among others, they have assessed the lift and drag forces on the rudder. One of the outcomes of this study was an asymmetric lift curve; for negative rudder angles the rudder seems to stall at angles more than five degrees smaller than for the positive rudder angles.
The goal for this research is to find and clarify the physical phenomenon which induces the rudder to stall at smaller rudder angles when subjected to a negative rudder angle (during bearing away). The main question to be answered in this report is: What physical phenomenon is at the basis of the asymmetric stalling behaviour on the rudder of a sailing yacht?
Towing tank tests are used to validate the data from Keuning et al. (2007). After which RANS CFD simulations are conducted in NUMECA to compare the towing tank tests to and to visualise the wake of the yacht in attempt to clarify the phenomena found.
A number of conclusions were found in this study. Firstly, the results of the towing tank experiments showed similarities to the previous experiments by Keuning et al. (2007). Differences are found in stall angles for positive rudder angles. These differences raise questions on the correctness of either of the experiments.
Secondly, no reasonable explanation is found for the negative drag forces found in the towing tank experiments. It is expected that these originate from the set-up of the rudder.
Thirdly, the lift curve found in the experiments is confirmed by the CFD data for the test cases. The physical effect behind the early stall behaviour of the rudder is still unknown. It is indicated that a part of the decrease in stall angle, a couple of degrees, is caused by the influence of the keel, when the disturbance passes on the low pressure side of the rudder. The hull is responsible for the remaining decrease. The CFD data indicates an influence of the vorticity of the keel and the boundary of the hull to cause a disturbance on the rudder.
Further research in necessary to clarify the results found in this study.
The goal for this research is to find and clarify the physical phenomenon which induces the rudder to stall at smaller rudder angles when subjected to a negative rudder angle (during bearing away). The main question to be answered in this report is: What physical phenomenon is at the basis of the asymmetric stalling behaviour on the rudder of a sailing yacht?
Towing tank tests are used to validate the data from Keuning et al. (2007). After which RANS CFD simulations are conducted in NUMECA to compare the towing tank tests to and to visualise the wake of the yacht in attempt to clarify the phenomena found.
A number of conclusions were found in this study. Firstly, the results of the towing tank experiments showed similarities to the previous experiments by Keuning et al. (2007). Differences are found in stall angles for positive rudder angles. These differences raise questions on the correctness of either of the experiments.
Secondly, no reasonable explanation is found for the negative drag forces found in the towing tank experiments. It is expected that these originate from the set-up of the rudder.
Thirdly, the lift curve found in the experiments is confirmed by the CFD data for the test cases. The physical effect behind the early stall behaviour of the rudder is still unknown. It is indicated that a part of the decrease in stall angle, a couple of degrees, is caused by the influence of the keel, when the disturbance passes on the low pressure side of the rudder. The hull is responsible for the remaining decrease. The CFD data indicates an influence of the vorticity of the keel and the boundary of the hull to cause a disturbance on the rudder.
Further research in necessary to clarify the results found in this study.
Master thesis
(2018)
-
Daan Geldermans, Riaan van 't Veer, Mark Leslie-Miller, Lex Keuning, Geert Keetels, Ido Akkerman
Dykstra Naval Architects are regularly designing large classic sailing yachts or motor-sailors, of which the draft is an important design restriction.The sailing performance is increased by adding lift-generating appendages,without increasing the draft. An example is a retractable centre board, havinga big influence on the sailing properties. Predicting the performance of the centre board contribution in a hull-keel-centre board configuration is the subject of this research. When predicting the performance of large sailing yachts, Dykstra wants to keep the ability to superpose an appendage to the data of a hull-keel configuration obtained from towing tank experiments or CFD simulations. This means that a method must be developed to estimate the contribution of the centre board, in terms of side force, resistance and centre of effort. Both towing tank experiments and CFD simulations are conducted for this research. The Maltese Falcon is used as the 'case ship'. A towing tank model of the Maltese Falcon was already made and tested at the TU delft in 2002. This model is again subjected to towing tank experiments, with a new keel and two new centre boards, resulting in 9 different hull-keel-centre board configurations. The main focus was on the towing tank experiments, executed in the Delft Hydromechanics Laboratory. CFD simulations were done to validate the results of the towing tank experiments and to gain visual insight in the flow around the vessel. The lift-carry-over on the keel and hull above the centre board can clearly be seen, as well as the influence of the centre board on the circulation in the flow around the underwater body of the yacht. After post-processing all experimental data, the results of the towing tank experiments are used to develop formulations to predict the performance contribution of the centre board. The measured lift of the centre board contribution was roughly a factor 2 higher than the centre would generate according to Wicker & Fehlner theory. Additionally, it was found that the lift-carry-over does not only have a positive effect on the generated side force, but also on the resistance. Furthermore, it was found that heeling the Maltese Falcon model by 15 degrees, yields the same magnitude oflift-carry-over as for the upright conditions. This resulted in the conclusion that heeling the yacht has no influence on the lift-carry-over from centre board to keel-hull. The new prediction methods, derived from the towing tank experiment data, are validated on YACHT1 and Adela. These are existing yachts with hull-keel-centre board configurations, but both very different. This enabled an interesting examination on the influence of certain aspects of the configuration on the performance of the centre board contribution. All in all, it was found that the predicted centre board contribution corresponded really well to the measured data of YACHT1 and Adela. This provides enough trust to implement the new centre board performance prediction methods in the Dykstra performance prediction tool. Every new design cycle of a yacht with hull-keel-centre board configuration will serve as a validation of the derived performance prediction methods.
...
Dykstra Naval Architects are regularly designing large classic sailing yachts or motor-sailors, of which the draft is an important design restriction.The sailing performance is increased by adding lift-generating appendages,without increasing the draft. An example is a retractable centre board, havinga big influence on the sailing properties. Predicting the performance of the centre board contribution in a hull-keel-centre board configuration is the subject of this research. When predicting the performance of large sailing yachts, Dykstra wants to keep the ability to superpose an appendage to the data of a hull-keel configuration obtained from towing tank experiments or CFD simulations. This means that a method must be developed to estimate the contribution of the centre board, in terms of side force, resistance and centre of effort. Both towing tank experiments and CFD simulations are conducted for this research. The Maltese Falcon is used as the 'case ship'. A towing tank model of the Maltese Falcon was already made and tested at the TU delft in 2002. This model is again subjected to towing tank experiments, with a new keel and two new centre boards, resulting in 9 different hull-keel-centre board configurations. The main focus was on the towing tank experiments, executed in the Delft Hydromechanics Laboratory. CFD simulations were done to validate the results of the towing tank experiments and to gain visual insight in the flow around the vessel. The lift-carry-over on the keel and hull above the centre board can clearly be seen, as well as the influence of the centre board on the circulation in the flow around the underwater body of the yacht. After post-processing all experimental data, the results of the towing tank experiments are used to develop formulations to predict the performance contribution of the centre board. The measured lift of the centre board contribution was roughly a factor 2 higher than the centre would generate according to Wicker & Fehlner theory. Additionally, it was found that the lift-carry-over does not only have a positive effect on the generated side force, but also on the resistance. Furthermore, it was found that heeling the Maltese Falcon model by 15 degrees, yields the same magnitude oflift-carry-over as for the upright conditions. This resulted in the conclusion that heeling the yacht has no influence on the lift-carry-over from centre board to keel-hull. The new prediction methods, derived from the towing tank experiment data, are validated on YACHT1 and Adela. These are existing yachts with hull-keel-centre board configurations, but both very different. This enabled an interesting examination on the influence of certain aspects of the configuration on the performance of the centre board contribution. All in all, it was found that the predicted centre board contribution corresponded really well to the measured data of YACHT1 and Adela. This provides enough trust to implement the new centre board performance prediction methods in the Dykstra performance prediction tool. Every new design cycle of a yacht with hull-keel-centre board configuration will serve as a validation of the derived performance prediction methods.