A revision of the popular equation of Richardson and Zaki (1954a, Transactions of the Institute of Chemical Engineering, 32, 35–53) for the hindered settling of suspensions of non-cohesive particles in fluids is proposed, based on 548 data sets from a broad range of scientific disciplines. The new hindered settling equation enables predictions of settling velocity for a wide range of particle sizes and densities, and liquid densities and viscosities, but with a focus on sediment particles in water. The analysis of the relationship between hindered settling velocity and particle size presented here shows that the hindered settling effect increases as the particle size decreases, for example, a 50% reduction in settling velocity is reached for 0.025 mm silt and 4 mm pebbles at particle concentrations of 13% and 25% respectively. Moreover, hindered settling starts to influence the settling behaviour of sediment particles at volumetric concentrations of merely a few per cent. For example, the particle settling velocity in flows that carry 5% silt is reduced by at least 22%. These observations suggest that hindered settling greatly increases the efficiency of natural flows to transport sediment particles, but also particulate carbon and pollutants, such as plastics, over large distances.@en

Bypassing turbidity currents can travel downslope without depositing any of their suspended sediment load. Along the way, they may encounter a slope break (i.e. an abrupt decrease in slope angle) that initiates sediment deposition. Depending on the initiation point of deposition (the upslope pinch-out), these turbidite deposits in slope-break systems can form potential reservoirs for hydrocarbons. Here we investigate the distribution of turbidite deposits as a function of the geometry of slope-break systems in flume experiments. Shields-scaled turbidity currents were released into a flume tank containing an upper and a lower slope reach separated by a slope break. These slope-break experiments were generating both depositional and bypassing flows solely based on variation in steepness of the lower and upper slope. Results show that the depositional pattern in a slope-break system is controlled by the steepness of the upper and lower slope, rather than the angle of the slope break. The steepness of the upper slope controls the upslope pinch-out, while the lower slope controls the deposit thickness downstream of the slope break.@en

Bypassing turbidity currents can travel downslope without depositing any of their suspended sediment load. Along the way, they may encounter a slope break (i.e. an abrupt decrease in slope angle) that initiates sediment deposition. Depending on the initiation point of deposition (the upslope pinch-out), these turbidite deposits in slope-break systems can form potential reservoirs for hydrocarbons. Here we investigate the distribution of turbidite deposits as a function of the geometry of slope-break systems in flume experiments. Shields-scaled turbidity currents were released into a flume tank containing an upper and a lower slope reach separated by a slope break. These slope-break experiments were generating both depositional and bypassing flows solely based on variation in steepness of the lower and upper slope. Results show that the depositional pattern in a slope-break system is controlled by the steepness of the upper and lower slope, rather than the angle of the slope break. The steepness of the upper slope controls the upslope pinch-out, while the lower slope controls the deposit thickness downstream of the slope break.@en

This study presents a classification for subaqueous clay-laden sediment gravity flows. A series of laboratory flume experiments were performed using 9%, 15%, and 21% sediment mixture concentrations composed of sand, silt, clay, and tap water, on varying bed slopes of 6°, 8°, and 9.5°, and with discharge rates of 10 and 15 m3/hr. In addition to the characteristics of the boundary and plug layers, which have been previously used for the classification of open-channel clay-laden flows, the newly presented classification also incorporates the treatment of the free shear layer. The flow states within the boundary and free shear layers were established using calculation of the inner variable, self-similarity considerations, and the magnitude of the apparent viscosity. Based on the experimental observations four flow types were recognized: (1) a clay-rich plug flow with a laminar free shear layer, a plug layer, and a laminar boundary layer, (2) a top transitional plug flow containing a turbulent free shear layer, a plug layer, and a laminar boundary layer, (3) a transitional turbidity current with a turbulent free shear layer, no plug layer, and a laminar boundary layer, and (4) a fully turbulent turbidity current. A connection between the emplaced deposits and the relevant flow types is drawn and it is shown that a Froude number, two Reynolds numbers, and a dimensionless yield stress parameter are sufficient to associate an experimental flow type with a natural large-scale density flow.@en

A new viscoelastic constitutive model for subaqueous clay-rich gravity flows is presented. It is explained that for the materials which exhibit a minimum in their strain controlled flow curves the structure parameter must be a symmetric function of the strain rate and the stress. Therefore, the destruction of structure within the material is modeled using the dissipation energy. An expression for the elastic strain of the flowing structure is derived. The final set of equations can reproduce the viscosity bifurcation that clay suspensions may exhibit under a given load. This is explained to be important for the prediction of the run-out distance of clay-rich gravity flows. The ability of the model to reproduce the general response of pasty materials to step stress and step shear rate tests is examined. The model requires four empirical parameters. A methodology is presented for obtaining these parameters and power law functions are given for their calculations for a limited rest time of 3000 s. The ability of the model to reproduce the rheological behavior that clay-rich suspensions exhibit under both stress and strain controlled conditions is examined using rheometry tests.@en