With the improvement of computational capability, finite element simulation is an increasingly practical method to accurately predict the ultimate capacity and ductile fracture behavior of high-strength bolts. However, the mesh size affects the results of FE simulations but related research on mesh size effects is relatively limited. In the present contribution, the mesoscale critical equivalent plastic strain (MCEPS) is used as a failure index for calibrating the parameters of ductile fracture locus of high-strength bolts with different mesh sizes. The identified fracture locus is compared with a large bulk of experimental data taken from the previously published literature. The results showed that mesh size can have high effects on the calibrated parameters of the plastic constitutive relationship after necking and ductile fracture locus of high-strength bolts.@en

Wind, as a sustainable and affordable energy source, represents a strong alternative to traditional energy sources. However, wind power is only one of the options, together with other renewable energy sources. Consequently, the core concerns for wind turbine manufacturers and operators are to increase its reliability and decrease costs, therefore enhancing commercial competitiveness. Among typical failure modes of wind turbines, fatigue is a common and critical source. Given the significance of fatigue reliability in wind turbine structural integrity, reliable probabilistic fatigue theories are necessary for design scheme optimization. By reducing the expenses on manufacturing, operation, and maintenance in reliability- and cost-optimal ways, the cost of energy can be significantly reduced. This study systematically reviews the state-of-the-art technology for fatigue reliability of wind turbines, and elaborates on the evolution of methodology in wind load uncertainty modelling. In addition, fatigue reliability assessment techniques on four typical components are summarized. Finally, discussions and conclusions are presented, intending to provide direct insights into future theoretical development and methodological innovation in this field.@en

Among the possible future Internet architectures, Information Centric Networking (ICN) is the most promising one and researchers working on the Named Data Networking (NDN) project are putting efforts towards its deployment in a real scenario. To properly handle content names, the different components of an NDN network need efficient and scalable data structures. In this paper, we propose a new data structure to support the NDN forwarding procedure by replacing the current Forwarding Information Base (FIB): the Spatial Bloom Filter (SBF), a probabilistic data structure that guarantees fast lookup and efficient memory consumption. Through a set of simulations run to compare the performance of FIB and SBF, we found that the latter uses less than 5 KB of data to handle 106 queried interests, with a (negligible) probability 10-4 of false positive events. Conversely, the FIB requires up to 2.5 GB of data in disadvantageous cases, e.g. when interests are composed of a considerable number of components.@en

Nominal stresses have been used for a long time for the assessment of fatigue resistance of welded joints, however, this approach has strong limitations since the definition of the nominal stress may be subjective for complex welded details and/or complex loading. On the other hand, the hot-spot stress approach has been proposed to overcome these limitations considering the structural geometrical discontinuities. However, the hot-spot stress methods also present certain limitations, and the present study aims at evaluating the available numerical and analytical hot-spot stress methods proposed by DNVGL (2016) and IIW (2014). The particular case of an offshore tubular KT joint has been considered herein and discretized in two planes. It has been studied numerically using the ABAQUS software coupled with the hot-spot stress extrapolation methods described in IIW (2014) and DNVGL (2016). The influence of the weld geometry has been considered and evaluated. In addition to the numerical method, the present study has also considered the analytical approach proposed in DNVGL (2016) derived from the combination of Efthymiou solutions for the stress concentration factor with the method of superposition of stresses. The numerical models according to IIW (2014) have been found to be more conservative when compared with the mesh-size methods proposed by DNVGL (2016), both in numerical modelling without the weld or with weld. For the numerical models with weld cord, the mean values of normalized difference index obtained for all braces together, as a result of comparing numerical results with analytical solutions, are lower, when compared with results obtained from the numerical models without weld cord.@en

Accurately obtaining the material parameters of the damage model is very important for the ductile fracture simulation of steel structures made of high strength steel (HSS). The combination of micromechanics with the uncoupled phenomenological fracture model can be used to obtain the material parameters of ductile fracture locus only from the uniaxial engineering stress-strain relationship. A micro failure index is generally used to link the material fracture under different multiaxial stress status. It is relatively difficult to describe the irregular micro-void evolution using the microvoid radius, and also difficult to tackle the micro void coalescence of the mesoscale using microvoid volume fraction. The mesoscale critical equivalent plastic strain (MCEPS) is proposed as the failure index at the unit cell level to calibrate the fracture locus of the uncoupled phenomenological model in this paper. The fracture locus of the HSS is calibrated by comparing the FE results with experimental data using the homogenized MCEPS and maximum MCEPS at the microvoid surface, respectively. The identified fracture locus is further validated against five stress status, including butterfly shear specimen, butterfly tension specimen, the tensile specimen with the symmetric round notch, tension specimen with a central hole in the middle, and Sandia fracture challenge specimens in 2014. The comparisons of predictions with the experimental results showed that the proposed MCEPS index can be used to obtain the material parameters of the ductile fracture locus.@en

Wire arc additive manufacturing (WAAM) has increasingly attracted attention in the construction sector because of its ability to produce large metallic structural parts in short times. In this paper, Coffin-Manson and Morrow (CMM) equation is employed to compare the fatigue life of WAAM stainless steel with the structural steels S355 and S690. The results showed that the fatigue performance of structural steel is better than the WAAM stainless steel, the fatigue performance vertical to printing direction (WAAM-900) is better than it along the printing direction (WAAM-00). In addition, the fatigue cycle of the transition reversals of structural steel is much less than it of WAAM stainless. With the increasing the fatigue cycle, the maximum density of the strain amplitude ratio is gradually increased to 1.0. The probabilistic parameters of CMM equation were obtained by a stochastic analysis using Latin hypercube sampling strategies. The probabilistic strain-fatigue life behaviour obtained from the constant exponent sampling strategy is higher when compared with the varied exponent sampling strategy for both WAAM stainless and structural steels.@en

The fatigue resistance of welded connections made of high strength steel (HSS) is one of the most important topics for the application of HSS in the construction sector. One of the most challenging issues is how to predict the fatigue life of welded structures with complex geometry based on the test results from relatively simple coupon specimens. However, there are generally pre-existing residual stresses in the welded coupon specimens during fatigue tests, and these residual stresses vary greatly in welded structures with complex geometry. This increases the difficulty in predicting the fatigue behaviour of welded structures based on results at coupon scale. Hence, it is important to establish a relationship between the residual stress independent material characteristics and fatigue life. The fatigue behaviour of complex welded structures can be predicted by this residual stress independent material characteristics calibrated at the coupon level and simulated local residual stress distribution. In this paper, the residual stress-free characteristics, hardness, is employed to predict the fatigue life of butt-welded joints. Besides, the residual stress of V-shaped butt welds on a plate made of high strength steels are analysed by modelling of the welding process based on subsequent thermal analysis and mechanical stress analysis by implementing kill/birth strategies. The results show that it contributes to a better prediction compared with experimental results after considering the residual stress effects.@en

In this paper, a numerical simulation method of mixed-mode fatigue crack propagation was explored using the extended finite element method (XFEM) and the Virtual Crack Closure Technique (VCCT). Both 2D and 3D numerical models were selected to simulate the fatigue crack propagation of steel specimens. Two coefficients were proposed to calculate the equivalent energy release rate (Geq) for a better simulation of the mixed-mode fatigue crack propagation of S355 steel. The Walker equation and the calculation formula of Geq were realized by a user-defined subroutine. A set of optimal correction coefficients of mode II energy release rate (GII) and mode III energy release rate (GIII) were quantitatively comparing the simulation results and test data. The results will contribute to fatigue crack propagation prediction of steel structures in the civil engineering field.@en

Strengthening fatigue damage of orthotropic steel decks (OSDs) needs to comprehensively consider the strengthening effect and the dead weight introduced during the strengthening process, especially for OSDs in super large-span bridges or old renovated bridges, where the dead weight cannot be significantly increased during repair and maintenance. This paper proposed a new CFRP prestressed reinforcement method, that does not significantly increase dead weight while effectively inhibiting fatigue crack growth. The strengthening effects of various strengthening methods on the fatigue crack propagation of rib to deck joint in OSDs were compared. Besides, the strengthening effects of different crack sizes were also analyzed. The results showed that the proposed method is effective in reducing fatigue damage at the rib to deck joint in OSDs.@en

The ductile performance of high strength steel (HSS) from different steel grades, producers, manufacturing processes varies a lot. It is also difficult to conduct all kinds of reliable experiments to generate different stress status through different initial specimen geometries or by applying different load combinations in the civil engineering sector. One of the common issues for HSS structures is to identify the parameters of the ductile fracture model conveniently from the uniaxial stress–strain relationship obtained from common coupon specimens. An attempt is made in this paper to use the proposed mesoscale critical equivalent plastic strain (MCEPS) to calibrate the fracture locus of the uncoupled phenomenological model based only on the engineering stress–strain relationship. The proposed method is successfully validated by the Sandia fracture challenge in 2014.@en

Hole patterns are common in engineering design for connections and/or assembly purposes. Geometrical discontinuities can cause stress concentration in localized areas, making them more prone to fatigue crack initiation and influencing the fatigue life of the overall unit. In the past, much effort has been exerted on fatigue modelling of holed plates from both experimental and theoretical perspectives. However, most studied objects were aluminium or titanium thin plates for aviation purposes. In this work, the fatigue performance of a downscaled holed thick steel plate, extracted from a novel C1 Wedge Connection for wind turbine tower assembling, was tested and categorized according to commonly used industry codes. In particular, the influence of the surface size effect was experimentally observed and computationally discussed. Finally, a probabilistic fatigue model was proposed, which gives a favourable prediction on the fatigue behaviour of the surface polished holed thick steel plate with the help of the Smith–Watson–Topper (SWT) model.@en