Current groundwater treatment facilities, mostly relying on aeration-filtration configurations, aim at the removal of iron (Fe), ammonia (NH 4 + ) and manganese (Mn). However, recently water companies expressed the ambition to also reduce arsenic (As) concentrations in these rapid sand filters. The aim of this study was to investigate the effect of the Fe oxidation state entering a biological filter bed on As removal. By varying supernatant water level, either Fe(II) or Fe(III) in the form of hydrous ferric oxides (HFO) could be stimulated to enter the filter bed at alkaline groundwater pH (7.6). The experimental pilot column filters showed that once the As(III) oxidation stabilised in the top layer of the filter sand, As removal reached its maximum (±75% at 120 cm supernatant level and 1.5 m/h filtration velocity). The increase in supernatant level from 5 to 120 cm resulted in additional HFO production prior to rapid filtration (1.5, 5 and 10 m/h), i.e. homogeneous Fe(II) oxidation and flocculation, and subsequently, HFO ending up deeper into the filter bed (120 cm filter depth). At a low supernatant water level of 5 cm, Fe(II) oxidised heterogeneously and was removed within the top 20 cm of the filter bed. Consequently, filters with high supernatant levels removed As to lower levels (by 20%) than in filters with low supernatant water levels. The benefits of Fe(II) oxidation prior to filtration for As removal was confirmed by comparing Fe(III) to Fe(II) additions in the supernatant water or in the filter bed. Overall it is concluded that in biological groundwater filters, the combination of a higher supernatant level and/or Fe(III) addition with biological As(III) oxidation in the top of the filter bed promotes As removal. @en

The aim of this study was to identify bacteria present in ripened manganese removal filters for drinking water production. The bacterial population was identified with 'next generation' DNA sequencing, and specific bacteria were quantified with quantitative polymerase chain reaction (qPCR) and characterized by matrix-assisted laser desorption/ionization time-of-flight mass spectrometry (MALDI-TOF MS) analysis. The 'next generation' DNA sequencing analysis showed a bacteria population shift from the iron oxidizing species Gallionella spp. in the Fe-filter to manganese and nitrite oxidizing species Pseudomonas spp. and Nitrospira spp., respectively, present in the manganese removal filter. qPCR analysis confirmed the presence of a low concentration of the wellknown Mn2-oxidizing species Ps. putida in the manganese removal filter backwash water. Bacteria of the genus Pseudomonas, isolated from backwash water from a manganese removal filter were cultured and identified with MALDI-TOF MS analysis. Amongst others, P. gessardii, P. grimontii, and P. koreensis were identified. The presence of several manganese oxidizing bacteria species in ripened filter media supports the assumption that a microbial consortium is involved in the oxidation of manganese. Understanding the mechanisms by which manganese coating of filter media commences could endorse the creation of conditions favouring Birnessite formation, and possibly help in reducing typically long ripening periods of manganese removal filters with virgin filter media.@en

The aim of this study was to identify bacteria present in ripened manganese removal filters for drinking water production. The bacterial population was identified with 'next generation' DNA sequencing, and specific bacteria were quantified with quantitative polymerase chain reaction (qPCR) and characterized by matrix-assisted laser desorption/ionization time-of-flight mass spectrometry (MALDI-TOF MS) analysis. The 'next generation' DNA sequencing analysis showed a bacteria population shift from the iron oxidizing species Gallionella spp. in the Fe-filter to manganese and nitrite oxidizing species Pseudomonas spp. and Nitrospira spp., respectively, present in the manganese removal filter. qPCR analysis confirmed the presence of a low concentration of the wellknown Mn2-oxidizing species Ps. putida in the manganese removal filter backwash water. Bacteria of the genus Pseudomonas, isolated from backwash water from a manganese removal filter were cultured and identified with MALDI-TOF MS analysis. Amongst others, P. gessardii, P. grimontii, and P. koreensis were identified. The presence of several manganese oxidizing bacteria species in ripened filter media supports the assumption that a microbial consortium is involved in the oxidation of manganese. Understanding the mechanisms by which manganese coating of filter media commences could endorse the creation of conditions favouring Birnessite formation, and possibly help in reducing typically long ripening periods of manganese removal filters with virgin filter media.@en

The aim of this study was to identify bacteria present in ripened manganese removal filters for drinking water production. The bacterial population was identified with 'next generation' DNA sequencing, and specific bacteria were quantified with quantitative polymerase chain reaction (qPCR) and characterized by matrix-assisted laser desorption/ionization time-of-flight mass spectrometry (MALDI-TOF MS) analysis. The 'next generation' DNA sequencing analysis showed a bacteria population shift from the iron oxidizing species Gallionella spp. in the Fe-filter to manganese and nitrite oxidizing species Pseudomonas spp. and Nitrospira spp., respectively, present in the manganese removal filter. qPCR analysis confirmed the presence of a low concentration of the wellknown Mn2-oxidizing species Ps. putida in the manganese removal filter backwash water. Bacteria of the genus Pseudomonas, isolated from backwash water from a manganese removal filter were cultured and identified with MALDI-TOF MS analysis. Amongst others, P. gessardii, P. grimontii, and P. koreensis were identified. The presence of several manganese oxidizing bacteria species in ripened filter media supports the assumption that a microbial consortium is involved in the oxidation of manganese. Understanding the mechanisms by which manganese coating of filter media commences could endorse the creation of conditions favouring Birnessite formation, and possibly help in reducing typically long ripening periods of manganese removal filters with virgin filter media.@en

The aim of this study was to identify bacteria present in ripened manganese removal filters for drinking water production. The bacterial population was identified with 'next generation' DNA sequencing, and specific bacteria were quantified with quantitative polymerase chain reaction (qPCR) and characterized by matrix-assisted laser desorption/ionization time-of-flight mass spectrometry (MALDI-TOF MS) analysis. The 'next generation' DNA sequencing analysis showed a bacteria population shift from the iron oxidizing species Gallionella spp. in the Fe-filter to manganese and nitrite oxidizing species Pseudomonas spp. and Nitrospira spp., respectively, present in the manganese removal filter. qPCR analysis confirmed the presence of a low concentration of the wellknown Mn2-oxidizing species Ps. putida in the manganese removal filter backwash water. Bacteria of the genus Pseudomonas, isolated from backwash water from a manganese removal filter were cultured and identified with MALDI-TOF MS analysis. Amongst others, P. gessardii, P. grimontii, and P. koreensis were identified. The presence of several manganese oxidizing bacteria species in ripened filter media supports the assumption that a microbial consortium is involved in the oxidation of manganese. Understanding the mechanisms by which manganese coating of filter media commences could endorse the creation of conditions favouring Birnessite formation, and possibly help in reducing typically long ripening periods of manganese removal filters with virgin filter media.@en

The aim of this study was to identify bacteria present in ripened manganese removal filters for drinking water production. The bacterial population was identified with 'next generation' DNA sequencing, and specific bacteria were quantified with quantitative polymerase chain reaction (qPCR) and characterized by matrix-assisted laser desorption/ionization time-of-flight mass spectrometry (MALDI-TOF MS) analysis. The 'next generation' DNA sequencing analysis showed a bacteria population shift from the iron oxidizing species Gallionella spp. in the Fe-filter to manganese and nitrite oxidizing species Pseudomonas spp. and Nitrospira spp., respectively, present in the manganese removal filter. qPCR analysis confirmed the presence of a low concentration of the wellknown Mn2-oxidizing species Ps. putida in the manganese removal filter backwash water. Bacteria of the genus Pseudomonas, isolated from backwash water from a manganese removal filter were cultured and identified with MALDI-TOF MS analysis. Amongst others, P. gessardii, P. grimontii, and P. koreensis were identified. The presence of several manganese oxidizing bacteria species in ripened filter media supports the assumption that a microbial consortium is involved in the oxidation of manganese. Understanding the mechanisms by which manganese coating of filter media commences could endorse the creation of conditions favouring Birnessite formation, and possibly help in reducing typically long ripening periods of manganese removal filters with virgin filter media.@en

Relatively long operational time is required to achieve effective manganese removal in conventional aeration-filtration groundwater treatment with virgin filter media. Ripening period depends on water quality, operational parameters, and the filter media used. This study assessed the role of filter media type, backwashing and iron loading on the time required to achieve very effective manganese removal. Filter runs were conducted with two set-ups each with six pilot filters with virgin sand or anthracite, and different types of manganese oxide coated sand/anthracite (MOCS/MOCA). Pre-treated groundwater (aeration-rapid sand filtration), either directly, or after an additional pre-treatment (ultrafiltration-UF), was used as feed water. UF pre-treatment eliminated head loss development in pilot filters and backwashing was consequently not required. Filters that received feed water without UF pre-treatment required backwashing after 14 d of continuous operation. Use of virgin sand and anthracite resulted in comparable ripening time (25 d and 14 d for feed water without and with UF pre-treatment, respectively). Use of fresh MOCS/MOCA directly taken from operational filters, eliminated the need for ripening of virgin filter media, while dried MOCS was less effective than fresh one, while the total period required to achieve highly effective manganese removal (≥95%) was not shortened.@en

Relatively long operational time is required to achieve effective manganese removal in conventional aeration-filtration groundwater treatment with virgin filter media. Ripening period depends on water quality, operational parameters, and the filter media used. This study assessed the role of filter media type, backwashing and iron loading on the time required to achieve very effective manganese removal. Filter runs were conducted with two set-ups each with six pilot filters with virgin sand or anthracite, and different types of manganese oxide coated sand/anthracite (MOCS/MOCA). Pre-treated groundwater (aeration-rapid sand filtration), either directly, or after an additional pre-treatment (ultrafiltration-UF), was used as feed water. UF pre-treatment eliminated head loss development in pilot filters and backwashing was consequently not required. Filters that received feed water without UF pre-treatment required backwashing after 14 d of continuous operation. Use of virgin sand and anthracite resulted in comparable ripening time (25 d and 14 d for feed water without and with UF pre-treatment, respectively). Use of fresh MOCS/MOCA directly taken from operational filters, eliminated the need for ripening of virgin filter media, while dried MOCS was less effective than fresh one, while the total period required to achieve highly effective manganese removal (≥95%) was not shortened.@en

Relatively long operational time is required to achieve effective manganese removal in conventional aeration-filtration groundwater treatment with virgin filter media. Ripening period depends on water quality, operational parameters, and the filter media used. This study assessed the role of filter media type, backwashing and iron loading on the time required to achieve very effective manganese removal. Filter runs were conducted with two set-ups each with six pilot filters with virgin sand or anthracite, and different types of manganese oxide coated sand/anthracite (MOCS/MOCA). Pre-treated groundwater (aeration-rapid sand filtration), either directly, or after an additional pre-treatment (ultrafiltration-UF), was used as feed water. UF pre-treatment eliminated head loss development in pilot filters and backwashing was consequently not required. Filters that received feed water without UF pre-treatment required backwashing after 14 d of continuous operation. Use of virgin sand and anthracite resulted in comparable ripening time (25 d and 14 d for feed water without and with UF pre-treatment, respectively). Use of fresh MOCS/MOCA directly taken from operational filters, eliminated the need for ripening of virgin filter media, while dried MOCS was less effective than fresh one, while the total period required to achieve highly effective manganese removal (≥95%) was not shortened.@en

Relatively long operational time is required to achieve effective manganese removal in conventional aeration-filtration groundwater treatment with virgin filter media. Ripening period depends on water quality, operational parameters, and the filter media used. This study assessed the role of filter media type, backwashing and iron loading on the time required to achieve very effective manganese removal. Filter runs were conducted with two set-ups each with six pilot filters with virgin sand or anthracite, and different types of manganese oxide coated sand/anthracite (MOCS/MOCA). Pre-treated groundwater (aeration-rapid sand filtration), either directly, or after an additional pre-treatment (ultrafiltration-UF), was used as feed water. UF pre-treatment eliminated head loss development in pilot filters and backwashing was consequently not required. Filters that received feed water without UF pre-treatment required backwashing after 14 d of continuous operation. Use of virgin sand and anthracite resulted in comparable ripening time (25 d and 14 d for feed water without and with UF pre-treatment, respectively). Use of fresh MOCS/MOCA directly taken from operational filters, eliminated the need for ripening of virgin filter media, while dried MOCS was less effective than fresh one, while the total period required to achieve highly effective manganese removal (≥95%) was not shortened.@en

Relatively long operational time is required to achieve effective manganese removal in conventional aeration-filtration groundwater treatment with virgin filter media. Ripening period depends on water quality, operational parameters, and the filter media used. This study assessed the role of filter media type, backwashing and iron loading on the time required to achieve very effective manganese removal. Filter runs were conducted with two set-ups each with six pilot filters with virgin sand or anthracite, and different types of manganese oxide coated sand/anthracite (MOCS/MOCA). Pre-treated groundwater (aeration-rapid sand filtration), either directly, or after an additional pre-treatment (ultrafiltration-UF), was used as feed water. UF pre-treatment eliminated head loss development in pilot filters and backwashing was consequently not required. Filters that received feed water without UF pre-treatment required backwashing after 14 d of continuous operation. Use of virgin sand and anthracite resulted in comparable ripening time (25 d and 14 d for feed water without and with UF pre-treatment, respectively). Use of fresh MOCS/MOCA directly taken from operational filters, eliminated the need for ripening of virgin filter media, while dried MOCS was less effective than fresh one, while the total period required to achieve highly effective manganese removal (≥95%) was not shortened.@en

Relatively long operational time is required to achieve effective manganese removal in conventional aeration-filtration groundwater treatment with virgin filter media. Ripening period depends on water quality, operational parameters, and the filter media used. This study assessed the role of filter media type, backwashing and iron loading on the time required to achieve very effective manganese removal. Filter runs were conducted with two set-ups each with six pilot filters with virgin sand or anthracite, and different types of manganese oxide coated sand/anthracite (MOCS/MOCA). Pre-treated groundwater (aeration-rapid sand filtration), either directly, or after an additional pre-treatment (ultrafiltration-UF), was used as feed water. UF pre-treatment eliminated head loss development in pilot filters and backwashing was consequently not required. Filters that received feed water without UF pre-treatment required backwashing after 14 d of continuous operation. Use of virgin sand and anthracite resulted in comparable ripening time (25 d and 14 d for feed water without and with UF pre-treatment, respectively). Use of fresh MOCS/MOCA directly taken from operational filters, eliminated the need for ripening of virgin filter media, while dried MOCS was less effective than fresh one, while the total period required to achieve highly effective manganese removal (≥95%) was not shortened.@en

Relatively long operational time is required to achieve effective manganese removal in conventional aeration-filtration groundwater treatment with virgin filter media. Ripening period depends on water quality, operational parameters, and the filter media used. This study assessed the role of filter media type, backwashing and iron loading on the time required to achieve very effective manganese removal. Filter runs were conducted with two set-ups each with six pilot filters with virgin sand or anthracite, and different types of manganese oxide coated sand/anthracite (MOCS/MOCA). Pre-treated groundwater (aeration-rapid sand filtration), either directly, or after an additional pre-treatment (ultrafiltration-UF), was used as feed water. UF pre-treatment eliminated head loss development in pilot filters and backwashing was consequently not required. Filters that received feed water without UF pre-treatment required backwashing after 14 d of continuous operation. Use of virgin sand and anthracite resulted in comparable ripening time (25 d and 14 d for feed water without and with UF pre-treatment, respectively). Use of fresh MOCS/MOCA directly taken from operational filters, eliminated the need for ripening of virgin filter media, while dried MOCS was less effective than fresh one, while the total period required to achieve highly effective manganese removal (≥95%) was not shortened.@en

Eind 2014 ontstond de Contactgroep Drinkwater Technologen in Nederland en Vlaanderen uit een fusie tussen de contactgroepen ontharding en filtratie. Technologen van tien Nederlandse en vier Vlaamse waterbedrijven en kennisinstituut KWR delen actief kennis over (drink)watertechnologie.@en