The Ultraviolet Imager (UVI) is a challenging instrument developed in the frame of the SMILE mission, a collaboration between ESA and CAS. The UVI instrument is a CMOS-based ultraviolet camera developed to image Earth's northern auroral regions. It is centered on the 160-180 nm UV waveband, with a 10° × 10° field of view. At the core of the instrument, four thin film-coated mirrors guide light into its detector and ensure most of the signal filtering, crucial to achieve an out-of-band rejection ratio as low as possible to reject light from solar diffusion, dayglow and unwanted atomic lines. We developed an interferometric coating based on an MgF2/LaF3 multilayer stack deposited by ion-assisted electron-beam deposition. We gradually improved our evaporation setup to reach a high degree of homogeneity, precision and repeatability on the material thicknesses, over the entire mirrors surface. The reflectivity maximum is above 85% and the wavelength at which it occurs is adjustable within 1 nm, while the out-of-band reflectivity between 120 and 155 nm and between 200 nm and 1100 nm is kept below 6% on average never exceeding 8 %. The coating has been space qualified and shows stable performances in conditions representative of the instrument operation environment (thermal cycling under vacuum, radiations, UV exposure…).

Stray light represents a major performance limitation for optical instruments. Analyses are done with ray-tracing software to evaluate the stray light performances of a design and, if necessary, improve it before manufacturing. Accurate simulations, however, require sending a sufficient number of rays. Hence, the process can be very time-consuming. We introduce the concept of stray light entrance pupil (SLEP) and demonstrate how it can be an efficient tool for simulating stray light for point sources. The SLEP defines a pupil over which light entering the optical system generates stray light reaching the detector. When that pupil is smaller than the first lens of the system, rays can be sent only through that pupil instead of the full lens aperture. Therefore, the time required to perform the simulation is reduced. Moreover, the efficiency can be further improved by defining a source with nonuniform ray density. The SLEP method is demonstrated on a wide-angle Earth observation camera and a time reduction up to about 20 is obtained. The SLEP concept can also be used to facilitate experimental characterization.

The Ultraviolet Imager (UVI) instrument is a very challenging imager developed in the frame of the SMILE-ESA mission. The UV camera will consist of a single imaging system targeted at a portion of the Lyman-Birge-Hopfield (LBH) N2 wavelength band. The baseline design of the imager meets the requirements to record snapshots of auroral dynamics with sufficient spatial resolution to measure cusp processes (100 km) under fully sunlit conditions from the specified apogee of the spacecraft. To achieve this goal, the UVI instrument utilizes a combination of four on-axis mirrors with an intensified FUV CMOS based camera. The mirrors will be coated with spectral selective interferometric layers to provide most of the signal filtering. The objective of these filters is to select the scientific waveband between 160 and 180 nm. The combined four mirrors have to give an out-of-band rejection ratio as high as possible to reject light from solar diffusion, dayglow and unwanted atomic lines in a range of 10-8-10-9. Different multilayer coatings are considered and optimized according to the π-multilayer equation for different H/L ratio and for different angles of incidence. Our theoretical evaluation shows a least a modification of the reflectance spectrum as a function of the angle of incidence, so that the optical beams hitting the different mirrors can have different optical properties depending on the optical fields and the distribution of the rays on the pupil. In this paper the effect of fields and coating homogeneity on the spectral throughput of the UVI instrument will be assessed and described.

In this article, we propose a new solar concentrator based on spectral splitting of sunlight. Spectral splitting has the objective to collect different spectra onto spectrally adapted solar cells for a more efficient use of the Sun's spectrum. Its combination with solar concentration makes an alternative to classical technologies. The proposed concentrator is composed of a diffractive/refractive optical element that spectrally splits and focuses the light onto a waveguide. The light is then conducted by total internal reflection towards the two specific solar cells. The optical concept and optimization of each element is presented in this paper. An adaptation for dye sensitized solar cells is performed. A geometrical factor around 5× is reached. Finally, theoretical optical efficiency, the manufacturing process and experimental testing with a collimated Sun simulator are presented.

The ICON mission is led by the University of California-Berkeley (Space Sciences Laboratory). In the frame of this mission the Space Center of Liege was involved in the optical design optimization and related analysis, and VUV on ground calibration.

ICON FUV is a two channel spectrographic imager that measures intensity and spatial distribution of oxygen (135.6 nm) and molecular nitrogen (157 nm) of the ionosphere. As those wavelengths are strongly absorbed by the atmosphere, the optical elements of the system have to be tested inside vacuum chambers. Prior to the instrument alignment and calibration, two 3600 gr/mm gratings were characterized. The primary focus is the measurement of the diffraction efficiencies; while the second objective is to select the best grating and to define which is the flight and the spare. A dedicated setup has been developed to assess the grating optical performances under vacuum. A 1 cm diameter collimated beam is generated using an off-axis parabola and a UV source at its focal point. The grating is placed at the center of two rotation stages collinearly aligned. One detector is placed on a rotating arm, deported from its rotation center. A PMT detector records diffracted light intensity with respect to its angular position and its wavelength. Angular incidence on the grating is tuned with the help of the second rotation stage. The grating efficiency homogeneity and scattering properties are measured through a Y-X scan.

The optical calibration of the ICON-FUV instrument requires designing specific ground support equipment (GSE). The ICON-FUV instrument is a spectrographic imager that operates on two specific wavelengths in the UV (135.6 nm and 157 nm). All the operations have to be performed under vacuum UV light. The optical setup is based on a VUV monochromator coupled with a collimator that illuminates the FUV entrance slit. The instrument is placed on a manipulator providing fields pointing. Image quality and spectral properties can be then characterized for each field. OGSE, MGSE, optical calibration plan and vacuum alignment of the instrument are described.

We present a new solar concentrator concept. This concept is based on spectral splitting. It implies reflective, refractive and diffractive elements that allow two spectrally differentiated beams to reach different and/or unmatched lattice solar cells. The aimed geometrical concentration factor is 5× and the theoretical optical efficiency of that concentrator concept reaches theoretically 82%. The following study will discuss the concept of such a solar concentrator. A practical application to dye sensitized solar cells is given. The manufacturing and design of the element is then exposed. Those elements have been tested in the laboratory. Good agreements with theoretical simulations are demonstrated.