Pressure on the coastline is escalating due to the impacts of climate change, this is leading to a rise in sea-levels and intensifying storminess. Consequently, many regions of the coast are at increased risk of erosion and flooding. Therefore coastal protection schemes will increase in cost and scale. In response there is a growing use of nature-based coastal protection which aim to be sustainable, effective and adaptable. An example of a nature-based solution is a dynamic cobble berm revetment: a berm constructed from cobble and other gravel sediments at the high tide wave runup limit. These structures limit wave excursion protecting the hinterland from inundation, stabilise the upper beach and adapt to changes in water level. Recent experiments and field applications have shown the suitability of these structures for coastal protection, however many of the processes and design considerations are poorly understood. This study directly compares two prototype scale laboratory experiments which tested dynamic cobble berm revetments constructed with approximately the same geometry but differing gravel characteristics; well-sorted rounded gravel (DynaRev1) and poorly-sorted angular gravel (DynaRev2). In both cases the structures were tested using identical wave forcing including incrementally increasing water level and erosive wave conditions. The results presented in this paper demonstrate that both designs responded to changing water level and wave conditions by approaching a dynamically stable state, where individual gravel is mobilised under wave action but the geometry remains approximately constant. Further, both structures acted to reduce swash excursions compared to a pure sand beach. However, their morphological behaviour is response to wave action varied considerably. Once overtopping of the designed crest occurred, the poorly-sorted revetment developed a peaked crest which grew in elevation as the water level or wave height increased, further limited overtopping. By comparison, the well-sorted revetment was characterised by a larger volume of submerged gravel and a lower elevation flat crest which responded less well to changes in conditions. This occurred due to two processes: (1) for the poorly-sorted case, gravel sorting processes moved small to medium gravel material (D₅₀<70mm) to the crest and (2) the angular nature of the poorly-sorted gravel material promoted increased interlocking. Both of these processes led to a gravel matrix that is more resistant to wave action and gravitational effects. Both revetments experienced some sinking due to sand erosion beneath the front slope. The rate of sinking for the well-sorted case was larger and continued throughout due to the large pore spaces within the gravel matrix. For the poorly sorted revetment in DynaRev2, sand erosion ceased after approximately 28 h due to the development of a filter layer of small gravel at the sand-gravel interface reducing porosity at this location, hence a larger volume of sand was preserved beneath the structure. Both designs present a low-cost and effective solution for protecting sandy coastlines but from an engineering viewpoint it appears better to avoid well-sorted gravel material and greater gravel angularity has been seen to increase crest stability.

@en

The present paper reports on a field experiment performed over a shallow, roughness-varying barrier reef at Maupiti island, French Polynesia. The spectral wave energy balance is examined, outside the breaking zone and accounting for non-linear transfers and mean current, to estimate the wave friction factor. This latter varies from 0.05 to 4, with dependence on the ratio between near-bed orbital amplitude and roughness height well predicted by an adjusted parameterization from Madsen (1995). The present results are discussed with respect to other field data recovered on coral and rocky grounds.

@en

The effects of climate change and sea level rise, combined with overpopulation are leading to ever-increasing stress on coastal regions throughout the world. As a result, there is increased interest in sustainable and adaptable methods of coastal protection. Dynamic cobble berm revetments consist of a gravel berm installed close to the high tide shoreline on a sand beach and are designed to mimic naturally occurring composite beaches (dissipative sandy beaches with a gravel berm around the high tide shoreline). Existing approaches to predict wave runup on sand or pure gravel beaches have very poor skill for composite beaches and this restricts the ability of coastal engineers to assess flood risks at existing sites or design new protection structures. This paper presents high-resolution measurements of wave runup from five field and large-scale laboratory experiments investigating composite beaches and dynamic cobble berm revetments. These data demonstrated that as the swash zone transitions from the fronting sand beach to the gravel berm, the short-wave component of significant swash height rapidly increases and can dominate over the infragravity component. When the berm toe is submerged at high tide, it was found that wave runup is strongly controlled by the water depth at the toe of the gravel berm. This is due to the decoupling of the significant wave height at the berm toe from the offshore wave conditions due to the dissipative nature of the fronting sand beach. This insight, combined with new methods to predict wave setup and infragravity wave dissipation on composite beaches is used to develop the first composite beach/dynamic revetment-specific methodologies for predicting wave runup.@en