This study aimed to assess the suitability of lime treatment for use in dikes in the Netherlands. The effect of this technique on the behavior of a Dutch clay was addressed by comparing the detailed response of lime-treated and natural samples at different lime contents (1.25% and 2.25%) and curing periods. A series of laboratory tests consisting of index classification, constant rate of strain, and triaxial and hole erosion tests were performed. The results demonstrated that lime treatment altered the soil response. Differences were observed in the physical, compressibility, strength, and erodibility properties. It was found that lime improved considerably the resistance to compression and erosion, but the effect on hydraulic conductivity was limited. The triaxial test results showed that lime treatment was particularly effective at low stress (<25 kPa) and low strain levels (<10%). During shearing, lime-treated samples exhibited dilative tendencies and enhanced effective strength properties until a stress-strain state was reached that was believed to be related to the breakage of the bonding structure of the sample. The findings of this study demonstrate that the merits of lime treatment can be of particular benefit in dike applications, particularly when the focus is on improving soil erosion resistance. @en

A series of undrained cyclic direct simple shear (CDSS) tests on dense Toyoura sand has been performed with the aim to investigate the influence of the stiffness of the DSS device on test results. To this end, springs were installed to reduce deliberately the stiffness of the apparatus. It is shown that the cyclic resistance of the sand depends strongly on the rigidity of the apparatus frame. In particular, as the stiffness of the DSS device increases, the number of loading cycles required to reach liquefaction decreases. This pronounced apparatus-stiffness dependence is of great practical concern in geotechnical engineering because it directly implies that the CDSS response of a soil sample can be predominantly controlled by the stiffness of the apparatus and not by the soil behavior alone. In addition, the test results indicate that the effect of equipment compliance in cyclic undrained DSS testing can be minimized when the ratio of the stiffness of the tested sand sample to the stiffness of the apparatus has a significantly low value.@en

The dynamic behavior of a peat deposit in the north of the Netherlands is described. The organic content ranges from 70% to 95%, which is high compared to the organic content generally presented in publications on the dynamic behavior of peats. Shear wave velocities vs and correspondingly small-strain shear moduli G0 closely match values stated in the literature. Correlations stated in the literature for predicting G0 proved to be applicable. Resonant column and cyclic direct simple shear tests were performed to establish the shear modulus reduction curves and damping curves. Excess pore pressure development during testing indicates dilatant behavior. The general trend shows nearly flat shear modulus reduction and damping curves at small strains regardless of organic content. Cyclic direct simple shear tests on humified material showed a larger pore pressure buildup than found in tests on non-to-moderately humified material. Differences in degree of humification did not result in significant differences in the shear modulus reduction curve, including G0 values. Large scatter was found in the damping curves. For the humified material, tested at low stress level, a discontinuity in the damping curve is found at shear strain of 3%, which corresponds to a rapid pore pressure buildup in the tests.@en

The dynamic behavior of a peat deposit in the north of the Netherlands is described. The organic content ranges from 70% to 95%, which is high compared to the organic content generally presented in publications on the dynamic behavior of peats. Shear wave velocities vs and correspondingly small-strain shear moduli G0 closely match values stated in the literature. Correlations stated in the literature for predicting G0 proved to be applicable. Resonant column and cyclic direct simple shear tests were performed to establish the shear modulus reduction curves and damping curves. Excess pore pressure development during testing indicates dilatant behavior. The general trend shows nearly flat shear modulus reduction and damping curves at small strains regardless of organic content. Cyclic direct simple shear tests on humified material showed a larger pore pressure buildup than found in tests on non-to-moderately humified material. Differences in degree of humification did not result in significant differences in the shear modulus reduction curve, including G0 values. Large scatter was found in the damping curves. For the humified material, tested at low stress level, a discontinuity in the damping curve is found at shear strain of 3%, which corresponds to a rapid pore pressure buildup in the tests.@en

The dynamic behavior of a peat deposit in the north of the Netherlands is described. The organic content ranges from 70% to 95%, which is high compared to the organic content generally presented in publications on the dynamic behavior of peats. Shear wave velocities vs and correspondingly small-strain shear moduli G0 closely match values stated in the literature. Correlations stated in the literature for predicting G0 proved to be applicable. Resonant column and cyclic direct simple shear tests were performed to establish the shear modulus reduction curves and damping curves. Excess pore pressure development during testing indicates dilatant behavior. The general trend shows nearly flat shear modulus reduction and damping curves at small strains regardless of organic content. Cyclic direct simple shear tests on humified material showed a larger pore pressure buildup than found in tests on non-to-moderately humified material. Differences in degree of humification did not result in significant differences in the shear modulus reduction curve, including G0 values. Large scatter was found in the damping curves. For the humified material, tested at low stress level, a discontinuity in the damping curve is found at shear strain of 3%, which corresponds to a rapid pore pressure buildup in the tests.@en