A large campaign of characterization of the ductile to brittle transition temperature (DBTT) and microstructure has been performed on several commercial and lab-scale pure tungsten grades, potassium doped tungsten alloys, and particle reinforced tungsten grades (with particles of TiC, Y₂O₃, or ZrC), all integrated in a large-scale neutron irradiation campaign. The DBTT is deduced based on miniaturized three-point bending tests to provide reference data for the assessment of the irradiation effects on the tungsten alloys. This miniaturized geometry is designed to minimize the operational cost of neutron irradiation, to speed up post-irradiation examination, and to reduce the amount of nuclear waste. The resulting DBTT ranges from around −15 up to 450 °C, depending on the material. The potassium doped tungsten alloys have the lowest DBTT, followed by rolled ZrC reinforced tungsten grade, commercial pure tungsten grades, lab-scale pure tungsten grades, and other particle reinforced tungsten grades. The crack plane orientation and microstructure with respect to grain shape and grain boundaries significantly affect the DBTT for forged/rolled tungsten products with elongated grains. The L-T orientation has a lower DBTT compared to the T-L orientation. Moreover, the DBTT difference in the L-T and T-L orientation raises with increasing the grain aspect ratio. An attempt is made to establish a relationship between the density of low and high angle grain boundaries and DBTT value. The obtained relationship is discussed in the frame of mechanical processing (i.e., rolling or forging) to optimize the DBTT by optimized manufacturing. The results are compared to recent computational predictions of the DBTT in tungsten.

Persulfates ((peroxymonosulfate (PMS) and peroxydisulfate (PDS)) can disintegrate waste activated sludge (WAS), but their influence on volatile fatty acid (VFA) production during anaerobic fermentation is largely unclear. Particularly, it is unknown whether persulfates can improve fermentation without any preactivation. This study investigated how the direct addition of PMS and PDS into the fermenter influences VFA production from WAS, and uncovered possible mechanisms of improved VFA production. At the PMS dosage of 1.0 mM/gVS, maximum VFA yield (1025 ± 55 mg COD/L) was observed in 5 days of fermentation, which was 24% higher than that with an equimolar addition of PDS and 132% higher than that without persulfate addition. However, the cost-effectiveness of PMS in enhancing VFA production is lower than that of PDS. The in situ generated hydroxyl and sulfate radicals from persulfates in the fermenter enhanced not only WAS disintegration and solubilization but also the formation of biodegradable substances for acidification. Moreover, the direct addition of persulfates into the fermenter shifted the microbial community toward hydrolysis-acidification such as Clostridium_sensu_stricto_10 and Fonticella. Results of this study also suggest that preactivation is not necessary when persulfates are applied to improve WAS fermentation.

Six tungsten grades were irradiated in the Belgian material test reactor (BR2) and characterized by Vickers hardness tests in order to investigate the irradiation-induced hardening. These tungsten grades included: Plansee (Austria) ITER specification tungsten, ALMT (Japan) ITER specification tungsten, two products from KIT (Germany) produced by powder injection molding (PIM) and strengthened by 1% TiC and 2% Y2O3 dispersed particles, and rolled tungsten strengthened by 0.5% ZrC from ISSP (China). The materials were irradiated face-to-face at three temperatures equal to 600 °C, 1000 °C, and 1200 °C to the dose of ∼1 dpa. The Vickers hardness tests under 200 gf (HV0.2) were performed at room temperature. The Vickers hardness increases as the irradiation temperature increases from 600 to 1000 °C for all materials, except for the ZrC-reinforced tungsten, for which the increase of hardness does not depend on irradiation temperature. The irradiation-induced hardness decreases after irradiation at 1200 °C. This is a result of defect annealing enhanced by thermally activated diffusion. However, even at 1200 °C, the impact of neutron irradiation on the hardness increase remains significant; the hardness increases by ∼30 to 60% compared to the non-irradiated value. In the case of TiC-strengthened material, the irradiation hardening progressively raises with irradiation temperature, which cannot be explained by the accumulation of neutron irradiation defects solely.

The Pearl River estuary is an ecologically dynamic region located in southern China that experiences strong gradients in its biogeochemical properties. This study examined the seasonality of nutrient dynamics, identified related environmental responses, and evaluated how river discharge regulated nutrient sink and source. The field investigation showed significant differences of dissolved nutrients with seasons and three zones of the estuary regarding the estuarine characteristics. Spatially, nutrients exhibited a clear decreasing trend along the salinity gradient; temporally, their levels were obviously higher in summer than other seasons. The aquatic environment was overall eutrophic, as a result of increased fluxes of nitrogen and silicate. This estuary was thus highly sensitive to nutrient enrichment and related pollution of eutrophication. River discharge, oceanic current, and atmospheric deposition distinctly influenced the nutrient status. These factors accordingly may influence phytoplankton that are of importance in coastal ecosystems. Phytoplankton (in terms of chlorophyll) was potentially phosphate limited, which then more frequently resulted in nutrient pollution and blooms. Additionally, the nutrient sources were implied according to the cause–effect chains between nutrients, hydrology, and chlorophyll, identified by the PCA-generated quantification. Nitrogen was constrained by marine-riverine waters and their mutual increase-decline trend, and a new source was supplemented along the transport from river to sea, while a different source of terrestrial emission from coastal cities contributed to phosphate greatly.

In recent years, volatile fatty acid (VFA) production through anaerobic fermentation of sewage sludge, instead of methane production, has been regarded as a high-value and promising roadmap for sludge stabilization and resource recovery. This review first presents the effects of some essential factors that influence VFA production and composition. In the second part, we present an extensive analysis of conventional pretreatment and co-fermentation strategies ultimately addressed to improving VFA production and composition. Also, the effectiveness of these approaches is summarized in terms of sludge degradation, hydrolysis rate, and VFA production and composition. According to published studies, it is concluded that some pretreatments such as alkaline and thermal pretreatment are the most effective ways to enhance VFA production from sewage sludge. The possible reasons for the improvement of VFA production by different methods are also discussed. Finally, this review also highlights several current technical challenges and opportunities in VFA production with spectrum control, and further related research is proposed.

The strength and ductility of two tungsten products, developed for application in nuclear fusion environment, are studied before and after neutron irradiation using uniaxial tensile tests. The first product is a commercially pure tungsten, produced by AT&M company according to ITER specification, and the second one is reinforced with zirconium carbide (W–ZrC) particles. The addition of ZrC particles leads to a reduction of the ductile to brittle transition temperature (DBTT) in non-irradiated conditions down to 50–100 °C without loss of strength and of other attractive properties of tungsten. The neutron irradiation was performed in the range 625–700 °C up to 1.125 dpa. The tests were performed to screen the shift of the DBTT as well as to characterize the evolution of the strength and ductility at the irradiation temperature. In addition, a series of interrupted tensile tests were performed in order to determine the variation of the yield strength as a function of temperature using an original single specimen test method. The neutron irradiation causes the reduction of the total elongation of both tungsten products. The DBTT range, which was evaluated from the tensile test results, of W–ZrC lies in the 300–500 °C range (while it is ∼100 °C in non-irradiated state). The DBTT range of pure tungsten is between 400 and 575 °C i.e. higher than that of W–ZrC. The irradiation hardening, measured at ∼600 °C, which is close to the irradiation temperature, leads to an increase of the proof stress by a factor of two in both studied grades. Despite that the irradiation induced hardening, both products retain a total elongation of about 10% prior to fracture. W–ZrC exhibits a similar total elongation at 500 °C, thus maintaining a significant ductility resource, while pure W becomes brittle at 500 °C and below.

Surface pretreatment is generally applied before application of protective coatings on Mg alloys, which influences surface microstructure and electrochemical activity of the substrate and has an effect on the coating properties. The effect of various pretreatment processes (sand-blasting, grinding and polishing) on the microstructure and corrosion protection performance of phosphate conversion coating (PCC) on AZ91D Mg alloy was investigated in the present study. Sand-blasting cleaning significantly increases the surface roughness and electrochemical activity of the substrate, leading to formation of a porous PCC with inferior corrosion protection performance. In the case of ground/polished Mg alloy, the uniformity and corrosion resistance of the resultant conversion coating are mainly related to the surface roughness. Relatively low surface roughness of the substrate facilitates formation of a corrosion protective PCC.

The preparation of thin lamellas by focused ion beam (FIB) for MEMS-based in situ TEM experiments is time consuming. Typically, the lamellas are of ~5μm*10μm and have a thickness less than 100nm. Here we demonstrate a fast lamellas’ preparation method using special fast cutting by FIB of samples prepared by conventional TEM sample preparation by argon ion milling or electrochemical polishing methods. This method has been applied successfully on various materials, such as ductile metallic alloy Ti₆₈Ta₂₇A_l5, brittle ceramics K_0.5Na_0.5NbO₃-6%LiNbO₃ and semiconductor Si. The thickness of the lamellas depends on the original TEM sample.

The structural evolution of Cu₄₅Zr₄₅Ag₁₀ metallic glass was investigated by in situ transmission electron microscopy heating experiments. The relationship between phase separation and crystallization was elucidated. Nucleation and growth-controlled nanoscale phase separation at early stage were seen to impede nanocrystallization, while a coarser phase separation via aggregation of Ag-rich nanospheres was found to promote the precipitation of Cu-rich nanocrystals. Coupling of composition and dynamics heterogeneities was supposed to play a key role during phase separation preceding crystallization.