This paper presents a novel approach integrating motion replanning, path tracking and vehicle stability for collision avoidance using nonlinear Model Predictive Contouring Control. Employing torque vectoring capabilities, the proposed controller is able to stabilise the vehicle in evasive manoeuvres at the limit of handling. A nonlinear double-track vehicle model, together with an extended Fiala tyre model, is used to capture the nonlinear coupled longitudinal and lateral dynamics. The optimised control inputs are the steering angle and the four longitudinal wheel forces to minimise the tracking error in safe situations and maximise the vehicle-to-obstacle distance in emergency manoeuvres. These optimised longitudinal forces generate an additional direct yaw moment, enhancing the vehicle’s lateral agility and aiding in obstacle avoidance and stability maintenance. The longitudinal tyre forces are constrained using the tyre friction cycle. The proposed controller has been tested on rapid prototyping hardware to prove real-time capability. In a high-fidelity simulation environment validated with experimental data, our proposed approach successfully avoids obstacles and maintains vehicle stability. It outperforms two baseline controllers: one without torque vectoring and another one without collision avoidance prioritisation. Furthermore, we demonstrate the robustness of the proposed approach to vehicle parameter variations, road friction, perception, and localisation errors. The influence of each variation is statistically assessed to evaluate its impact on the performance, providing guidelines for future controller design.

This paper presents a novel Learning-based Model Predictive Contouring Control (L-MPCC) algorithm for evasive manoeuvres at the limit of handling. The algorithm uses the Student-t Process (STP) to minimise model mismatches and uncertainties online. The proposed STP captures the mismatches between the prediction model and the measured lateral tyre forces and yaw rate. The mismatches correspond to the posterior means provided to the prediction model to improve its accuracy. Simultaneously, the posterior covariances are propagated to the vehicle lateral velocity and yaw rate along the prediction horizon. The STP posterior covariance directly depends on the variance of observed data, so its variance is more significant when the online measurements differ from the recorded ones in the training set and smaller in the opposite case. Thus, these covariances can be utilised in the L-MPCC’s cost function to minimise the vehicle state uncertainties. In a high-fidelity simulation environment, we demonstrate that the proposed L-MPCC can successfully avoid obstacles, keeping the vehicle stable while driving a double lane change manoeuvre at a higher velocity than an MPCC without STP. Furthermore, the proposed controller yields a significantly lower peak sideslip angle, improving the vehicle’s manoeuvrability compared to an L-MPCC with a Gaussian Process.

This paper presents an original approach to vehicle obstacle avoidance. It involves the development of a nonlinear Model Predictive Contouring Control, which uses torque vectoring to stabilise and drive the vehicle in evasive manoeuvres at the limit of handling. The proposed algorithm combines motion planning, path tracking and vehicle stability objectives, prioritising collision avoidance in emergencies. The controller's prediction model is a nonlinear double-track vehicle model based on an extended Fiala tyre to capture the nonlinear coupled longitudinal and lateral dynamics. The controller computes the optimal steering angle and the longitudinal forces per each of the four wheels to minimise tracking error in safe situations and maximise the vehicle-to-obstacle distance in emergencies. Thanks to the optimisation of the longitudinal tyre forces, the proposed controller can produce an extra yaw moment, increasing the vehicle's lateral agility to avoid obstacles while keeping the vehicle stable. The optimal forces are constrained in the tyre friction circle not to exceed the tyres and vehicle capabilities. In a high-fidelity simulation environment, we demonstrate the benefits of torque vectoring, showing that our proposed approach is capable of successfully avoiding obstacles and keeping the vehicle stable while driving a double-lane change manoeuvre, in comparison to baselines lacking torque vectoring or collision avoidance prioritisation.

This paper proposes a non-linear Model Predictive Contouring Control (MPCC) for obstacle avoidance in automated vehicles driven at the limit of handling. The proposed controller integrates motion planning, path tracking and vehicle stability objectives, prioritising obstacle avoidance in emergencies. The controller’s prediction model is a non-linear single-track vehicle model with the Fiala tyre to capture the vehicle’s non-linear behaviour. The MPCC computes the optimal steering angle and brake torques to minimise tracking error in safe situations and maximise the vehicle-to-obstacle distance in emergencies. Furthermore, the MPCC is extended with the tyre friction circle to fully exploit the vehicle’s manoeuvrability and stability. The MPCC controller is tested using real-time rapid prototyping hardware to prove its real-time capability. The performance is compared with a state-of-the-art Model Predictive Control (MPC) in a high-fidelity simulation environment. The double lane change scenario results demonstrate a significant improvement in successfully avoiding obstacles and maintaining vehicle stability.

This paper proposes a novel vehicle sideslip angle estimator, which uses the physical knowledge from an Unscented Kalman Filter (UKF) based on a non-linear single-track vehicle model to enhance the estimation accuracy of a Convolutional Neural Network (CNN). The model-based and data-driven approaches interact mutually, and both use the standard inertial measurement unit and the tyre forces measured by load sensing technology. CNN benefits from the UKF the capacity to leverage the laws of physics. Concurrently, the UKF uses the CNN outputs as sideslip angle pseudo-measurement and adaptive process noise parameters. The back-propagation through time algorithm is applied end-to-end to the CNN and the UKF to employ the mutualistic property. Using a large-scale experimental dataset of 216 manoeuvres containing a great diversity of vehicle behaviours, we demonstrate a significant improvement in the accuracy of the proposed architecture over the current state-of-art hybrid approach combined with model-based and data-driven techniques. In the case that a limited dataset is provided for the training phase, the proposed hybrid approach still guarantees estimation robustness.

In this article, we propose a tractable nonlinear fault estimation filter along with explicit performance bounds for a class of linear dynamical systems in the presence of both additive and nonlinear multiplicative faults. We consider the case, where both faults may occur simultaneously and through an identical dynamical relationship, a setting that is relevant to several application domains, including automotive driving, aviation, and chemical plants. The proposed filter architecture combines tools from model-based approaches in the control literature and regression techniques from machine learning. To this end, we view the regression operator through a system-theoretic perspective to develop operator bounds that are then utilized to derive performance bounds for the proposed estimation filter. In the case of constant, simultaneously, and identically acting additive and multiplicative faults, it can be shown that the estimation error converges to zero with an exponential rate. The performance of the proposed estimation filter in the presence of incipient faults is validated through an application on the lateral safety systems of SAE level 4 automated vehicles. The numerical results show that the theoretical bounds of this study are indeed close to the actual estimation error.

In this research a controller is developed that can control path-tracking both within and beyond stable limit handling. The controller is based on the equations of motion of the nonlinear bicycle model. The performance of the controller is evaluated in simulation, a sensitivity analysis is performed and the controller is implemented on a 1/10 scale radio controlled car. The controller is able to track a path in normal driving conditions and let the vehicle enter and maintain a drift while remaining close to the desired path.

Lateral control in the absence of lane markings is an essential safety fallback for an autonomous vehicle in cooperative driving applications. Point following control is one such solutions for lateral control. However, it suffers from corner cutting and severe disturbance amplification throughout the platoon. In this paper, a new model for controller synthesis is proposed which supports including the error induced by the road curvature in the communication between two vehicles. This enables the trailing vehicle to deduce the actual road error states, which negates steady-state corner cutting if these errors are controlled to zero. To demonstrate the benefits of this new control model, an control framework is used to design a lateral controller which minimizes the lateral overshoot of the vehicles during transient maneuvering. The proposed approach has been evaluated using numerical simulations. Simulation results show that the lateral overshoot can be reduced by a factor 10 with respect to existing lateral control solutions.

In this research a controller is developed that can control path-tracking both within and beyond stable limit handling. A controller is developed, based on the equations of motion of the nonlinear bicycle model. The performance of the controller is evaluated in both simulation and on a 1/10 scale radio controlled car. The controller is able to track a path in typical cornering conditions and let the vehicle enter and maintain a drift while remaining close to the desired path.