Titanium dioxide (TiO₂) has been widely used as a photocatalyst in CO₂ reduction reaction (CO₂RR) due to its low cost, high stability, and strong absorption in the close-to-visible ultra-violet (UV) range. However, TiO₂ films suffer from poor selectivity in CO₂ reduction due to their unfavorable electronic properties. In this work, we address this challenge by fabricating ultra-thin (14 nm) defective TiO₂ films (TiO₂-DTF) to enhance the selectivity of CO₂RR towards formate. TiO₂ sol was prepared using a facile and reproducible sol-gel method and directly deposited onto the surface of the electrode, forming a uniform, ultra-thin TiO₂ layers with a high number of defects. The activity of the TiO₂-DTF catalyst was studied in both photochemical and photoelectrochemical CO₂RR, indicating that the applied potential increases both the yield and selectivity of CO₂RR to formate. The TiO₂-DTF photocathode exhibited remarkable formate production during CO₂ reduction, achieving exceptional Faradaic efficiencies of up to 45 %. To elucidate the mechanism of photoelectrochemical CO₂RR on TiO₂-DTF, an in-situ attenuated total reflection Fourier-transform infrared spectroscopy (in-situ ATR-FTIR) was used and experimental results were supported by density functional theory (DFT) calculations. This study demonstrates that ultra-thin highly defective TiO₂ film, prepared using the cost-effective and environmentally friendly sol-gel method, can be used as photoelectrocatalyst for CO₂ reduction.

The development of advanced catalysts with innovative nanoarchitectures is critical for addressing energy and environmental challenges such as the electrochemical CO₂ reduction reaction (CO₂ RR). Herein, the synthesis of an innovative copper–sulfur planar structure, Cu–S–BDC, within a metal–organic framework (MOF) catalyst is presented, which demonstrates 100% selectivity toward formate as the sole carbon product. Structural analysis and surface characterizations reveal that Cu–S–BDC exhibits quasi-2D inorganic building units, with Cu bonded to two S-CH (Formula presented.) groups and one BDC linker, while carboxylate groups adopt a bridging coordination mode. This unique arrangement not only imparts remarkable structural stability but also enhances the electronic properties of the MOF, as evidenced by a narrow bandgap of 1.203 eV that facilitates efficient charge transfer and increased electrochemical current density in CO (Formula presented.) RR. Notably, it offers a Faradaic efficiency of 92% for formate at an overpotential as low as −0.4 V versus the reversible hydrogen electrode (RHE) in an aqueous electrolyte of 1 m KOH, as well as a current density of −25.8 mA cm² at −0.9 V versus RHE, averaged over 24 h of electrolysis. This study highlights a fresh perspective in the field of MOF electrocatalysts by demonstrating that engineering the metal coordination environment can significantly enhance the electronic properties and consequently improve the electrocatalytic performance of these materials.

Efficient and sustainable synthesis of performant metal/nitrogen-doped carbon (M-N-C) catalysts for oxygen reduction and evolution reactions (ORR/OER) is vital for the global switch to green energy technologies-fuel cells and metal-air batteries. This study reports a solid-phase template-assisted mechanosynthesis of Fe-N-C, featuring low-cost and sustainable FeCl₃, 2,4,6-tri(2-pyridyl)-1,3,5-triazine (TPTZ), and NaCl. A NaCl-templated Fe-TPTZ metal-organic material was formed using facile liquid-assisted grinding/compression. With NaCl, the Fe-TPTZ template-induced stability allows for a rapid, thus, energy-efficient pyrolysis. Among the produced materials, 3D-FeNC-LAG exhibits remarkable performance in ORR (E_1/2 = 0.85 V and E_onset = 1.00 V), OER (E_j=10 = 1.73 V), and in the zinc-air battery test (power density of 139 mW cm^-2). The multilayer stream mapping (MSM) framework is presented as a tool for creating a sustainability assessment protocol for the catalyst production process. MSM employs time, cost, resource, and energy efficiency as technoeconomic sustainability metrics to assess the potential upstream impact. MSM analysis shows that the 3D-FeNC-LAG synthesis exhibits 90% overall process efficiency and 97.67% cost efficiency. The proposed synthetic protocol requires 2 times less processing time and 3 times less energy without compromising the catalyst efficiency, superior to the most advanced methods.

Hafnia-based thin films exhibit unconventional ferroelectricity. These materials also show rich polymorphism, and thus temperature and field-driven phase transitions, as well as oxygen migration. In a bigger context of exploring the synergy between ferroelectricity and diffusion-based structural phenomena, here we study temperature-dependent phase transitions in epitaxial Hf0.5Zr0.5O2(HZO)/La0.67Sr0.33MnO3 (LSMO, bottom electrode) heterostructures. We report topotactic phase transitions and their clear pathways in both LSMO and HZO layers upon heating under vacuum, using in situ scanning transmission electron microscopy (STEM). Specifically, we directly image oxygen and cationic columns using integrated differential phase contrast STEM and follow their evolution with temperature. We also perform in situ high temperature X-ray diffraction in air and show that the LSMO layer undergoes reversible thermal expansion and contraction when heated up to 850 °C, whereas HZO undergoes strain relaxation beyond 750 °C without any reversible phase transition. Our results provide a comprehensive and direct understanding of temperature-dependent structure, defect, and property correlations in these systems.