In order to recruit neurons in excitable tissue, constant current neural stimulators are commonly used. Recently, ultra high-frequency (UHF) stimulation has been proposed and proven to have the same efficacy as constant-current stimulation. UHF stimulation uses a fundamentally different way of activating the tissue: each stimulation phase is made of a burst of current pulses with adjustable amplitude injected into the tissue at a high (e.g., 1 MHz) frequency. This paper presents the design, integrated circuit (IC) implementation, and measurement results of a power efficient multichannel UHF neural stimulator. The core of the neurostimulator is based on our previously proposed architecture of an inductor-based buck-boost dc-dc converter without the external output capacitor. The ultimate goal of this work is to increase the power efficiency of the UHF stimulator for multiple-channel operation, while keeping the number of external components minimal. To this end, a number of novel approaches were employed in the integrated circuit design domain. More specifically, a novel zero-current detection scheme is proposed. It allows to remove the freewheel diode typically used in dc-dc converters to prevent current to flow back from the load to the inductor. Furthermore, a gate-driver circuit is implemented which allows the use of thin gate-oxide transistors as high-voltage switches. By doing so, and exploiting the fundamental working principle of the proposed current-controlled UHF stimulator, the need for a high-voltage supply is eliminated and the stimulator is powered up from a 3.5 V input voltage. Both the current detection technique and the gate driving circuit of the current implementation allow to boost the power efficiency up to 300% when compared to previous UHF stimulator works. A peak power efficiency of 68% is achieved, while 8 independent channels with 16 fully configurable electrodes are used. The circuit is implemented in a 0.18 μm HV process, and the total chip area is 3.65 mm²

Neural stimulators have the potential of becoming very important devices for the treatment of a wide variety of diseases. One of the major problems with existing stimulators is the limited waveform adjustability. This precludes the use of sophisticated stimulation programs and thereby affects the efficacy of the therapy applied. For this reason a new type of stimulator is required.

A promising alternative for treating absence seizures has emerged through closed-loop neurostimulation, which utilizes a wearable or implantable device to detect and subsequently suppress epileptic seizures. Such devices should detect seizures fast and with high accuracy, while respecting the strict energy budget on which they operate. Previous work has overlooked one or more of these requirements, resulting in solutions which are not suitable for continuous closed-loop stimulation. In this paper, we perform an in-depth design space exploration of a novel seizure-detection algorithm, which uses a complex Morlet wavelet filter and a static thresholding mechanism to detect absence seizures. We consider both the accuracy and speed of our detection algorithm, as well as various trade-offs with device autonomy when executed on a low-power processor. For example, we demonstrate that a minimal decrease in average detection rate of only 1.83% (from 92.72% to 90.89%) allows for a substantial increase in device autonomy (of 3.7x) while also facilitating faster detection (from 710 ms to 540 ms).

This book discusses the design of neural stimulator systems which are used for the treatment of a wide variety of brain disorders such as Parkinson’s, depression and tinnitus. Whereas many existing books treating neural stimulation focus on one particular design aspect, such as the electrical design of the stimulator, this book uses a multidisciplinary approach: by combining the fields of neuroscience, electrophysiology and electrical engineering a thorough understanding of the complete neural stimulation chain is created (from the stimulation IC down to the neural cell). This multidisciplinary approach enables readers to gain new insights into stimulator design, while context is provided by presenting innovative design examples.

This paper presents a compact programmable biphasic stimulator for cochlear implants. By employing double-loop negative feedback, the output impedance of the current generator is increased, while maximizing the voltage compliance of the output transistor. To make the stimulator circuit compact, the stimulation current is set by scaling a reference current using a two stage binary-weighted transistor DAC (comprising a 3 bit high-voltage transistor DAC and a 4 bit low-voltage transistor DAC). With this structure the power consumption and the area of the circuit can be minimized. The proposed circuit has been implemented in AMS 0.18um high-voltage CMOS IC technology, using an active chip area of about 0.042mm^2. Measurement results show that proper charge balance of the anodic and cathodic stimulation phases is achieved and a dc blocking capacitor can be omitted. The resulting reduction in the required area makes the proposed system suitable for a large number of channels.

This paper presents a neural stimulator system that employs a fundamentally different way of stimulating neural tissue compared to classical constant current stimulation. A stimulation pulse is composed of a sequence of current pulses injected at a frequency of 1 MHz for which the duty cycle is used to control the stimulation intensity. The system features 8 independent channels that connect to any of the 16 electrodes at the output. A sophisticated control system allows for individual control of each channel's stimulation and timing parameters. This flexibility makes the system suitable for complex electrode configurations and current steering applications. Simultaneous multichannel stimulation is implemented using a high frequency alternating technique, which reduces the amount of electrode switches by a factor 8. The system has the advantage of requiring a single inductor as its only external component. Furthermore it offers a high power efficiency, which is nearly independent on both the voltage over the load as well as on the number of simultaneously operated channels. Measurements confirm this: in multichannel mode the power efficiency can be increased for specific cases to 40% compared to 20% that is achieved by state-of-the-art classical constant current stimulators with adaptive power supply.