Advances in CMOS technologies and circuit techniques have led to the development of continuous-time delta-sigma modulators (CTΔ Σ Ms) that sample at gigahertz (GHz) frequencies and achieve high linearity [-100 dBc and >120 dBFS spurious-free dynamic ranges (SFDRs)] in wide bandwidths (>100 MHz). However, at low frequencies (≤ 10 MHz), their performance is limited by the 1/f noise generated by the near-minimum size devices used in their wide-bandwidth input stages. This, in turn, limits their use in radio receivers intended to cover both the AM and FM bands. In this work, a multi-path multi-frequency chopping scheme is proposed to suppress 1/f noise, while preserving interferer robustness, thermal noise levels, and linearity. Implemented in a CTΔ Σ analog-to-digital converter (ADC) sampling at 6 GHz, it achieves a 22× reduction in 1/f noise, as well as 122-dBFS SFDR and -98.3-dBc THD in a 120-MHz BW.

Bias-flip rectifiers are commonly employed for piezoelectric energy harvesting (PEH). This article proposes a synchronized switch harvesting on an inductor (SSHI) rectifier with a duty-cycle-based (DCB) maximum power point tracking (MPPT) algorithm. The proposed DCB MPPT algorithm is based on the mathematically derived relation between the MPPT efficiency and the duty cycle of the bridge rectifier. The resulting equation shows that the MPPT efficiency only depends on the rectifier duty cycle, and is independent of any other system variables, such as voltage bias-flipping efficiency, the open-circuit voltage from the harvester, vibration frequency, etc. As a result, MPPT can be achieved by regulating the duty cycle, simplifying circuit implementation, and achieving self-regulating and continuous MPPT. This design was fabricated in a 180-nm BCD process. The measured results show 98% peak MPPT efficiency and up to 738% output power enhancement.

Advances in CMOS technologies have led to the development of continuous-time ΔΣ modulators (CTDSMs) with GHz sampling rates that achieve better than-100dBc linearity and bandwidths above 100MHz. However, at low frequencies (below 10MHz), their SNDR is limited by 1/f noise, which limits their use in radio receivers intended to cover both the AM and the FM bands. In this work, a multi-path multi-frequency chopping scheme is proposed to suppress 1/f noise, while maintaining interferer robustness, noise, spurious, and linearity performance. Implemented in a CTDSM sampling at 6GHz, it reduces its 1/f noise corner frequency by 22x and achieves -98.3dBc THD, 122dBFS SFDR in 120MHzBW.

Synchronized bias-flip rectifiers, such as synchronized switch harvesting on inductor (SSHI) rectifiers, are widely used for piezoelectric energy harvesting (PEH) [1], which can replace the use of batteries in many loT applications, thus reducing both system volume and maintenance cost. However, the output power extracted by such rectifiers strongly depends on the impedance matching between the piezoelectric transducer (PT) and the circuit. To maximize this, two maximum power point tracking (MPPT) algorithms are often used. As shown in Fig. 30.3.1 (left), the Perturb & Observe (P&O) (a.k.a. hill-climbing) algorithm adjusts the rectified output power in a stepwise manner towards the maximum power point (MPP), thus establishing robust and continuous MPPT. However, accurately sensing the rectified output power often requires complex and power-hungry hardware [1], [2]. Another simpler algorithm is based on the fractional open-circuit voltage (FOCV) and involves periodically measuring the PT's open-circuit voltage amplitude (VOC) and regulating the rectified voltage (VREC) to a level (VMPP), which corresponds to the MPP [3-6]. However, the PT must be periodically disconnected from the rectifier to measure VOC, resulting in wasted energy, while the inherent delay in sensing VOC variations reduces the overall tracking efficiency. Furthermore, a calibration step is usually necessary to determine VMPP, since this depends on the actual PT voltage flip efficiency (etaF) of the bias-flip rectifier.