Treating large bone defects is still a clinical challenge without perfect solution, mainly due to the unavailability of suitable bone implants. Additively manufactured (AM) absorbable porous metals provide unparalleled opportunities to realize the challenging requirements for bone-mimetic implants. Firstly, multi-scale geometries of such implants can be customized to mimic the micro-architecture and mechanical properties of human bone. The interconnected porous structure additionally increases the surface area to facilitate adhesion and proliferation of bone cells. Finally, their absorption properties are tunable to maintain the structural integrity of the implant throughout the bone healing process, ensuring sufficient loadbearing when needed and full disintegration after their job is done. Such a combination of properties paves the way for complete bone regeneration and remodeling. It is important to thoroughly characterize the biodegradation behavior, mechanical properties, and bone regeneration ability when developing ideal porous absorbable metal implants. We review the state-of-the-art of absorbable porous metals manufactured by selective laser melting (SLM), with a focus on geometrical design, material type, processing, and post-treatment. The impact of the latter aspects on absorption behavior, resulting mechanical properties, and cytocompatibility will also be briefly discussed. In comparison to their solid inert counterparts, AM absorbable porous metals (APMs) have shown many unique properties and hold tremendous potential to further optimize their application-specific performance due to their flexible geometrical design. We further highlight challenges in adopting AM APMs for future Orthopedic solutions.@en

Deployable meta-implants aim to minimize the invasiveness of orthopaedic surgeries by allowing for changes in their shape and size that are triggered by an external stimulus. Multi-stability enables deployable implants to transform their shape from some compact retracted state to the deployed state where they take their full sizes and are load-bearing. We combined multiple design features to develop a new generation of deployable orthopaedic implants. Kirigami cut patterns were used to create bi-stability in flat sheets which can be folded into deployable implants using origami techniques. Inspired by Russian dolls, we designed multi-layered specimens that allow for adjusting the mechanical properties and the geometrical features of the implants through the number of the layers. Because all layers are folded from a flat state, surface-related functionalities could be applied to our deployable implants. We fabricated specimens from polylactic acid, titanium sheets, and aluminum sheets, and demonstrated that a deployment ratio of up to ≈2 is possible. We performed experiments to characterize the deployment and load-bearing behavior of the specimens and found that the above-mentioned design variables allow for adjustments in the deployment force and the maximum force before failure. Finally, we demonstrate the possibility of decorating the specimens with micropatterns.@en

Additively manufactured (AM) porous structures are a new class of biomaterials with many advantages as compared to conventionally produced biomaterials. The goal of this study was to find out how the laser processing parameters including laser power and exposure time affect the mechanical properties, topology, and microstructure of porous biomaterials AM using a novel vector-based approach. Several cylindrical porous specimens were additively manufactured using a wide range of exposure time and laser power. The effects of those parameters on the surface roughness, strut diameter, relative density, hardness, elastic modulus, yield stress, first maximum stress, and plateau stress of the porous structures were studied. The results showed that the rate of change in mechanical and topological properties with respect to exposure time was non-linear while it was linear with respect to the laser power. The results also showed that the effects of laser power and exposure time on the mechanical properties and topology of AM porous structures could be decoupled from each other, enabling derivation of predictive emperical relationships. The emperical and experimental curves showed very good agreement, which further validates the validity of the separation method used for obtaining the emperical relationships. The analytical relationships for elastic modulus and yield stress that we had obtained in a previous study could predict the elastic modulus and yield stress of the porous strucutres when the energy input was high enough (i.e. exposure times ≥ 450 μs), because the local mechanical properties of the matrix material decreased for the lower levels of energy input. The change in the mechanical properties of the bulk material due to change in laser processing parameters should thus be taken into account.@en

Additively manufactured (AM) porous structures are a new class of biomaterials with many advantages as compared to conventionally produced biomaterials. The goal of this study was to find out how the laser processing parameters including laser power and exposure time affect the mechanical properties, topology, and microstructure of porous biomaterials AM using a novel vector-based approach. Several cylindrical porous specimens were additively manufactured using a wide range of exposure time and laser power. The effects of those parameters on the surface roughness, strut diameter, relative density, hardness, elastic modulus, yield stress, first maximum stress, and plateau stress of the porous structures were studied. The results showed that the rate of change in mechanical and topological properties with respect to exposure time was non-linear while it was linear with respect to the laser power. The results also showed that the effects of laser power and exposure time on the mechanical properties and topology of AM porous structures could be decoupled from each other, enabling derivation of predictive emperical relationships. The emperical and experimental curves showed very good agreement, which further validates the validity of the separation method used for obtaining the emperical relationships. The analytical relationships for elastic modulus and yield stress that we had obtained in a previous study could predict the elastic modulus and yield stress of the porous strucutres when the energy input was high enough (i.e. exposure times ≥ 450 μs), because the local mechanical properties of the matrix material decreased for the lower levels of energy input. The change in the mechanical properties of the bulk material due to change in laser processing parameters should thus be taken into account.@en

Recently, lattice titanium manufactured by additive manufacturing (AM) techniques has been utilized in various applications, including biomedical. The effects of topological design and processing parameters on the fatigue behaviour of such meta-biomaterials have been studied before. Most studies show that the fatigue life of additively manufactured lattice structures is limited. Post-processing techniques could play a major role in improving the fatigue of these promising biomaterials. This study aims to provide an in-depth investigation into the effects of heat treatments, hot isostatic pressing (HIP), sand blasting, and chemical etching on the microstructure, surface morphology, strength and fatigue resistance of selective laser melted titanium meta-biomaterials. It was found that the combination of microstructural design and surface engineering, induced by HIP and sand blasting respectively, allows to increase the endurance limit of these lattice meta-biomaterials by a factor of two. HIP treatment substantially decreased the internal porosity and transformed the microstructure to a more ductile mixture of α + β phases. Sand blasting allowed to eliminate surface imperfections and induced favourable compressive stress in the surface layer of the struts. Statement of Significance: Additively manufactured metallic meta-biomaterials are progressively being used as bone replacement orthopedic implants. While there is a great amount of research related to topological designs and their effect on mechanical (e.g. stiffness), physical (e.g. mass transport), and biological (e.g. osseointegration) properties, fatigue lifetime of such structures remains limited. This study provides fundamental investigation into the combined effect of microstructural design and surface engineering of titanium meta-biomaterial, enabled through various post treatment methods ranging from heat treatments to physical and chemical surface modifications. The findings show that fatigue life is significantly improved by applying developed herein novel method, which effortlessly can be used on other bone-mimicking metallic meta-biomaterials.@en

Recently, lattice titanium manufactured by additive manufacturing (AM) techniques has been utilized in various applications, including biomedical. The effects of topological design and processing parameters on the fatigue behaviour of such meta-biomaterials have been studied before. Most studies show that the fatigue life of additively manufactured lattice structures is limited. Post-processing techniques could play a major role in improving the fatigue of these promising biomaterials. This study aims to provide an in-depth investigation into the effects of heat treatments, hot isostatic pressing (HIP), sand blasting, and chemical etching on the microstructure, surface morphology, strength and fatigue resistance of selective laser melted titanium meta-biomaterials. It was found that the combination of microstructural design and surface engineering, induced by HIP and sand blasting respectively, allows to increase the endurance limit of these lattice meta-biomaterials by a factor of two. HIP treatment substantially decreased the internal porosity and transformed the microstructure to a more ductile mixture of α + β phases. Sand blasting allowed to eliminate surface imperfections and induced favourable compressive stress in the surface layer of the struts. Statement of Significance: Additively manufactured metallic meta-biomaterials are progressively being used as bone replacement orthopedic implants. While there is a great amount of research related to topological designs and their effect on mechanical (e.g. stiffness), physical (e.g. mass transport), and biological (e.g. osseointegration) properties, fatigue lifetime of such structures remains limited. This study provides fundamental investigation into the combined effect of microstructural design and surface engineering of titanium meta-biomaterial, enabled through various post treatment methods ranging from heat treatments to physical and chemical surface modifications. The findings show that fatigue life is significantly improved by applying developed herein novel method, which effortlessly can be used on other bone-mimicking metallic meta-biomaterials.@en

Recently, lattice titanium manufactured by additive manufacturing (AM) techniques has been utilized in various applications, including biomedical. The effects of topological design and processing parameters on the fatigue behaviour of such meta-biomaterials have been studied before. Most studies show that the fatigue life of additively manufactured lattice structures is limited. Post-processing techniques could play a major role in improving the fatigue of these promising biomaterials. This study aims to provide an in-depth investigation into the effects of heat treatments, hot isostatic pressing (HIP), sand blasting, and chemical etching on the microstructure, surface morphology, strength and fatigue resistance of selective laser melted titanium meta-biomaterials. It was found that the combination of microstructural design and surface engineering, induced by HIP and sand blasting respectively, allows to increase the endurance limit of these lattice meta-biomaterials by a factor of two. HIP treatment substantially decreased the internal porosity and transformed the microstructure to a more ductile mixture of α + β phases. Sand blasting allowed to eliminate surface imperfections and induced favourable compressive stress in the surface layer of the struts. Statement of Significance: Additively manufactured metallic meta-biomaterials are progressively being used as bone replacement orthopedic implants. While there is a great amount of research related to topological designs and their effect on mechanical (e.g. stiffness), physical (e.g. mass transport), and biological (e.g. osseointegration) properties, fatigue lifetime of such structures remains limited. This study provides fundamental investigation into the combined effect of microstructural design and surface engineering of titanium meta-biomaterial, enabled through various post treatment methods ranging from heat treatments to physical and chemical surface modifications. The findings show that fatigue life is significantly improved by applying developed herein novel method, which effortlessly can be used on other bone-mimicking metallic meta-biomaterials.@en

Recently, lattice titanium manufactured by additive manufacturing (AM) techniques has been utilized in various applications, including biomedical. The effects of topological design and processing parameters on the fatigue behaviour of such meta-biomaterials have been studied before. Most studies show that the fatigue life of additively manufactured lattice structures is limited. Post-processing techniques could play a major role in improving the fatigue of these promising biomaterials. This study aims to provide an in-depth investigation into the effects of heat treatments, hot isostatic pressing (HIP), sand blasting, and chemical etching on the microstructure, surface morphology, strength and fatigue resistance of selective laser melted titanium meta-biomaterials. It was found that the combination of microstructural design and surface engineering, induced by HIP and sand blasting respectively, allows to increase the endurance limit of these lattice meta-biomaterials by a factor of two. HIP treatment substantially decreased the internal porosity and transformed the microstructure to a more ductile mixture of α + β phases. Sand blasting allowed to eliminate surface imperfections and induced favourable compressive stress in the surface layer of the struts. Statement of Significance: Additively manufactured metallic meta-biomaterials are progressively being used as bone replacement orthopedic implants. While there is a great amount of research related to topological designs and their effect on mechanical (e.g. stiffness), physical (e.g. mass transport), and biological (e.g. osseointegration) properties, fatigue lifetime of such structures remains limited. This study provides fundamental investigation into the combined effect of microstructural design and surface engineering of titanium meta-biomaterial, enabled through various post treatment methods ranging from heat treatments to physical and chemical surface modifications. The findings show that fatigue life is significantly improved by applying developed herein novel method, which effortlessly can be used on other bone-mimicking metallic meta-biomaterials.@en

Recently, lattice titanium manufactured by additive manufacturing (AM) techniques has been utilized in various applications, including biomedical. The effects of topological design and processing parameters on the fatigue behaviour of such meta-biomaterials have been studied before. Most studies show that the fatigue life of additively manufactured lattice structures is limited. Post-processing techniques could play a major role in improving the fatigue of these promising biomaterials. This study aims to provide an in-depth investigation into the effects of heat treatments, hot isostatic pressing (HIP), sand blasting, and chemical etching on the microstructure, surface morphology, strength and fatigue resistance of selective laser melted titanium meta-biomaterials. It was found that the combination of microstructural design and surface engineering, induced by HIP and sand blasting respectively, allows to increase the endurance limit of these lattice meta-biomaterials by a factor of two. HIP treatment substantially decreased the internal porosity and transformed the microstructure to a more ductile mixture of α + β phases. Sand blasting allowed to eliminate surface imperfections and induced favourable compressive stress in the surface layer of the struts. Statement of Significance: Additively manufactured metallic meta-biomaterials are progressively being used as bone replacement orthopedic implants. While there is a great amount of research related to topological designs and their effect on mechanical (e.g. stiffness), physical (e.g. mass transport), and biological (e.g. osseointegration) properties, fatigue lifetime of such structures remains limited. This study provides fundamental investigation into the combined effect of microstructural design and surface engineering of titanium meta-biomaterial, enabled through various post treatment methods ranging from heat treatments to physical and chemical surface modifications. The findings show that fatigue life is significantly improved by applying developed herein novel method, which effortlessly can be used on other bone-mimicking metallic meta-biomaterials.@en

Recently, lattice titanium manufactured by additive manufacturing (AM) techniques has been utilized in various applications, including biomedical. The effects of topological design and processing parameters on the fatigue behaviour of such meta-biomaterials have been studied before. Most studies show that the fatigue life of additively manufactured lattice structures is limited. Post-processing techniques could play a major role in improving the fatigue of these promising biomaterials. This study aims to provide an in-depth investigation into the effects of heat treatments, hot isostatic pressing (HIP), sand blasting, and chemical etching on the microstructure, surface morphology, strength and fatigue resistance of selective laser melted titanium meta-biomaterials. It was found that the combination of microstructural design and surface engineering, induced by HIP and sand blasting respectively, allows to increase the endurance limit of these lattice meta-biomaterials by a factor of two. HIP treatment substantially decreased the internal porosity and transformed the microstructure to a more ductile mixture of α + β phases. Sand blasting allowed to eliminate surface imperfections and induced favourable compressive stress in the surface layer of the struts. Statement of Significance: Additively manufactured metallic meta-biomaterials are progressively being used as bone replacement orthopedic implants. While there is a great amount of research related to topological designs and their effect on mechanical (e.g. stiffness), physical (e.g. mass transport), and biological (e.g. osseointegration) properties, fatigue lifetime of such structures remains limited. This study provides fundamental investigation into the combined effect of microstructural design and surface engineering of titanium meta-biomaterial, enabled through various post treatment methods ranging from heat treatments to physical and chemical surface modifications. The findings show that fatigue life is significantly improved by applying developed herein novel method, which effortlessly can be used on other bone-mimicking metallic meta-biomaterials.@en

Recently, lattice titanium manufactured by additive manufacturing (AM) techniques has been utilized in various applications, including biomedical. The effects of topological design and processing parameters on the fatigue behaviour of such meta-biomaterials have been studied before. Most studies show that the fatigue life of additively manufactured lattice structures is limited. Post-processing techniques could play a major role in improving the fatigue of these promising biomaterials. This study aims to provide an in-depth investigation into the effects of heat treatments, hot isostatic pressing (HIP), sand blasting, and chemical etching on the microstructure, surface morphology, strength and fatigue resistance of selective laser melted titanium meta-biomaterials. It was found that the combination of microstructural design and surface engineering, induced by HIP and sand blasting respectively, allows to increase the endurance limit of these lattice meta-biomaterials by a factor of two. HIP treatment substantially decreased the internal porosity and transformed the microstructure to a more ductile mixture of α + β phases. Sand blasting allowed to eliminate surface imperfections and induced favourable compressive stress in the surface layer of the struts. Statement of Significance: Additively manufactured metallic meta-biomaterials are progressively being used as bone replacement orthopedic implants. While there is a great amount of research related to topological designs and their effect on mechanical (e.g. stiffness), physical (e.g. mass transport), and biological (e.g. osseointegration) properties, fatigue lifetime of such structures remains limited. This study provides fundamental investigation into the combined effect of microstructural design and surface engineering of titanium meta-biomaterial, enabled through various post treatment methods ranging from heat treatments to physical and chemical surface modifications. The findings show that fatigue life is significantly improved by applying developed herein novel method, which effortlessly can be used on other bone-mimicking metallic meta-biomaterials.@en

Recently, lattice titanium manufactured by additive manufacturing (AM) techniques has been utilized in various applications, including biomedical. The effects of topological design and processing parameters on the fatigue behaviour of such meta-biomaterials have been studied before. Most studies show that the fatigue life of additively manufactured lattice structures is limited. Post-processing techniques could play a major role in improving the fatigue of these promising biomaterials. This study aims to provide an in-depth investigation into the effects of heat treatments, hot isostatic pressing (HIP), sand blasting, and chemical etching on the microstructure, surface morphology, strength and fatigue resistance of selective laser melted titanium meta-biomaterials. It was found that the combination of microstructural design and surface engineering, induced by HIP and sand blasting respectively, allows to increase the endurance limit of these lattice meta-biomaterials by a factor of two. HIP treatment substantially decreased the internal porosity and transformed the microstructure to a more ductile mixture of α + β phases. Sand blasting allowed to eliminate surface imperfections and induced favourable compressive stress in the surface layer of the struts. Statement of Significance: Additively manufactured metallic meta-biomaterials are progressively being used as bone replacement orthopedic implants. While there is a great amount of research related to topological designs and their effect on mechanical (e.g. stiffness), physical (e.g. mass transport), and biological (e.g. osseointegration) properties, fatigue lifetime of such structures remains limited. This study provides fundamental investigation into the combined effect of microstructural design and surface engineering of titanium meta-biomaterial, enabled through various post treatment methods ranging from heat treatments to physical and chemical surface modifications. The findings show that fatigue life is significantly improved by applying developed herein novel method, which effortlessly can be used on other bone-mimicking metallic meta-biomaterials.@en

Additively manufactured (AM) degradable porous metallic biomaterials offer unique opportunities for satisfying the design requirements of an ideal bone substitute. Among the currently available biodegradable metals, iron has the highest elastic modulus, meaning that it would benefit the most from porous design. Given the successful preclinical applications of such biomaterials for the treatment of cardiovascular diseases, the moderate compatibility of AM porous iron with osteoblast-like cells, reported in earlier studies, has been surprising. This may be because, as opposed to static in vitro conditions, the biodegradation products of iron in vivo are transported away and excreted. To better mimic the in situ situations of biodegradable biomaterials after implantation, we compared the biodegradation behavior and cytocompatibility of AM porous iron under static conditions to the conditions with dynamic in situ-like fluid flow perfusion in a bioreactor. Furthermore, the compatibility of these scaffolds with four different cell types was evaluated to better understand the implications of these implants for the complex process of natural wound healing. These included endothelial cells, L929 fibroblasts, RAW264.7 macrophage-like cells, and osteoblastic MG-63 cells. The biodegradation rate of the scaffolds was significantly increased in the perfusion bioreactor as compared to static immersion. Under either condition, the compatibility with L929 cells was the best. Moreover, the compatibility with all the cell types was much enhanced under physiomimetic dynamic flow conditions as compared to static biodegradation. Our study highlights the importance of physiomimetic culture conditions and cell type selection when evaluating the cytocompatibility of degradable biomaterials in vitro. Statement of Significance: Additively manufactured (AM) degradable porous metals offer unique opportunities for the treatment of large bony defects. Despite the successful preclinical applications of biodegradable iron in the cardiovascular field, the moderate compatibility of AM porous iron with osteoblast-like cells was reported. To better mimic the in vivo condition, we compared the biodegradation behavior and cytocompatibility of AM porous iron under static condition to dynamic perfusion. Furthermore, the compatibility of these scaffolds with various cell types was evaluated to better simulate the process of natural wound healing. Our study suggests that AM porous iron holds great promise for orthopedic applications, while also highlighting the importance of physio-mimetic culture conditions and cell type selection when evaluating the cytocompatibility of degradable biomaterials in vitro.@en

The corrosion fatigue behavior of additively manufactured topologically ordered porous iron based on diamond unit cells was studied for the first time to understand its response to cyclic loading in a simulated physiological environment. The material exhibited high fatigue resistance with fatigue strengths being 70% and 65% of yield stress in air and revised simulated body fluid, respectively, mainly due to its slow degradation and excellent ductility. However, cyclic loading significantly increased biodegradation rate, especially at higher stress levels. The observed extraordinary fatigue strength, slow biodegradation and high ductility underline the importance of porous iron as a promising bone-substituting material.@en

Additively manufacturing (AM) opens up the possibility for biodegradable metals to possess uniquely combined characteristics that are desired for bone substitution, including bone-mimicking mechanical properties, topologically ordered porous structure, pore interconnectivity and biodegradability. Zinc is considered to be one of the promising biomaterials with respect to biodegradation rate and biocompatibility. However, no information regarding the biodegradability and biocompatibility of topologically ordered AM porous zinc is yet available. Here, we applied powder bed fusion to fabricate porous zinc with a topologically ordered diamond structure. An integrative study was conducted on the static and dynamic biodegradation behavior (in vitro, up to 4 weeks), evolution of mechanical properties with increasing immersion time, electrochemical performance, and biocompatibility of the AM porous zinc. The specimens lost 7.8% of their weight after 4 weeks of dynamic immersion in a revised simulated body fluid. The mechanisms of biodegradation were site-dependent and differed from the top of the specimens to the bottom. During the whole in vitro immersion time of 4 weeks, the elastic modulus values of the AM porous zinc (E = 700–1000 MPa) even increased and remained within the scope of those of cancellous bone. Indirect cytotoxicity revealed good cellular activity up to 72 h according to ISO 10,993–5 and -12. Live-dead staining confirmed good viability of MG-63 cells cultured on the surface of the AM porous zinc. These important findings could open up unprecedented opportunities for the development of multifunctional bone substituting materials that will enable reconstruction and regeneration of critical-size load-bearing bone defects. Statement of significance: No information regarding the biodegradability and biocompatibility of topologically ordered AM porous zinc is available. We applied selective laser melting to fabricate topologically ordered porous zinc and conducted a comprehensive study on the biodegradation behavior, electrochemical performance, time-dependent mechanical properties, and biocompatibility of the scaffolds. The specimens lost 7.8% of their weight after4 weeks dynamic biodegradation while their mechanical properties surprisingly increased after 4 weeks. Indirect cytotoxicity revealed good cellular activity up to 72 h. Intimate contact between MG-63 cells and the scaffolds was also observed. These important findings could open up unprecedented opportunities for the development of multifunctional bone substituting materials that mimic bone properties and enable full regeneration of critical-size load-bearing bony defects.@en

Additively manufactured (AM) topologically ordered porous metallic biomaterials with the proper biodegradation profile offer a unique combination of properties ideal for bone regeneration. These include a fully interconnected porous structure, bone-mimicking mechanical properties, and the possibility of fully regenerating bony defects. Most of such biomaterials are, however, based on magnesium and, thus, degrade too fast. Here, we present the first report on topologically ordered porous iron made by Direct Metal Printing (DMP). The topological design was based on a repetitive diamond unit cell. We conducted a comprehensive study on the in vitro biodegradation behavior (up to 28 days), electrochemical performance, time-dependent mechanical properties, and biocompatibility of the scaffolds. The mechanical properties of AM porous iron (E = 1600–1800 MPa) were still within the range of the values reported for trabecular bone after 28 days of biodegradation. Electrochemical tests showed up to ≈12 times higher rates of biodegradation for AM porous iron as compared to that of cold-rolled (CR) iron, while only 3.1% of weight loss was measured after 4 weeks of immersion tests. The biodegradation mechanisms were found to be topology-dependent and different between the periphery and central parts of the scaffolds. While direct contact between MG-63 cells and scaffolds revealed substantial and almost instant cytotoxicity in static cell culture, as compared to Ti-6Al-4V, the cytocompatibility according to ISO 10993 was reasonable in in vitro assays for up to 72 h. This study shows how DMP could be used to increase the surface area and decrease the grain sizes of topologically ordered porous metallic biomaterials made from metals that are usually considered to degrade too slowly (e.g., iron), opening up many new opportunities for the development of biodegradable metallic biomaterials. Statement of Significance: Biodegradation in general and proper biodegradation profile in particular are perhaps the most important requirements that additively manufactured (AM) topologically ordered porous metallic biomaterials should offer in order to become the ideal biomaterial for bone regeneration. Currently, most biodegradable metallic biomaterials are based on magnesium, which degrade fast with gas generation. Here, we present the first report on topologically ordered porous iron made by Direct Metal Printing (DMP). We also conducted a comprehensive study on the biodegradation behavior, electrochemical performance, biocompatibility, and the time evolution of the mechanical properties of the implants. We show that these implants possess bone-mimicking mechanical properties, accelerated degradation rate, and reasonable cytocompatibility, opening up many new opportunities for the development of iron-based biodegradable materials.@en

Partially due to the unavailability of ideal bone substitutes, the treatment of large bony defects remains one of the most important challenges of orthopedic surgery. Additively manufactured (AM) biodegradable porous metals that have emerged since 2018 provide unprecedented opportunities for fulfilling the requirements of an ideal bone implant. First, the multi-scale geometry of these implants can be customized to mimic the human bone in terms of both micro-architecture and mechanical properties. Second, a porous structure with interconnected pores possesses a large surface area, which is favorable for the adhesion and proliferation of cells and, thus, bony ingrowth. Finally, the freeform geometrical design of such biomaterials could be exploited to adjust their biodegradation behavior so as to maintain the structural integrity of the implant during the healing process while ensuring that the implant disappears afterwards, paving the way for full bone regeneration. While the AM biodegradable porous metals that have been studied so far have shown many unique properties as compared to their solid counterparts, the unprecedented degree of flexibility in their geometrical design has not yet been fully exploited to optimize their properties and performance. In order to develop the ideal bone implants, it is important to take advantage of the full potential of AM biodegradable porous metals through detailed and systematic study on their biodegradation behavior, mechanical properties, biocompatibility, and bone regeneration performance. This review paper presents the state of the art in AM biodegradable porous metals and is focused on the effects of material type, processing, geometrical design, and post-AM treatments on the mechanical properties, biodegradation behavior, in vitro biocompatibility, and in vivo bone regeneration performance of AM porous Mg, Fe, and Zn as well as their alloys. We also identify a number of knowledge gaps and the challenges encountered in adopting AM biodegradable porous metals for orthopedic applications and suggest some promising areas for future research.@en

Biodegradable porous magnesium (Mg) scaffolds are promising for application in the regeneration of critical-sized bone defects. Although additive manufacturing (AM) carries the promise of offering unique opportunities to fabricate porous Mg scaffolds, current attempts to apply the AM approach to fabricating Mg scaffolds have encountered some crucial issues, such as those related to safety in operation and to the difficulties in composition control. In this paper, we present a room-temperature extrusion-based AM method for the fabrication of topologically ordered porous Mg scaffolds. It is composed of three steps, namely (i) preparing a Mg powder loaded ink with desired rheological properties, (ii) solvent-cast 3D printing (SC-3DP) of the ink to form scaffolds with 0 °/ 90 °/ 0 ° layers, and (iii) debinding and sintering to remove the binder in the ink and then get Mg powder particles bonded by applying a liquid-phase sintering strategy. A rheological analysis of the prepared inks with 54, 58 and 62 vol% Mg powder loading was performed to reveal their viscoelastic properties. Thermal-gravimetric analysis (TGA), Fourier transform infrared spectroscopy (FTIR), carbon/sulfur analysis and scanning electron microscopy (SEM) indicated the possibilities of debinding and sintering at one single step for fabricating pure Mg scaffolds with high fidelity and densification. The resulting scaffolds with high porosity contained hierarchical and interconnected pores. This study, for the first time, demonstrated that the SC-3DP technique presents unprecedented possibilities to fabricate Mg-based porous scaffolds that have the potential to be used as a bone-substituting material. Statement of Significance: Biodegradable porous magnesium scaffolds are promising for application in the regeneration of critical-sized bone defects. Although additive manufacturing (AM) carries the promise of offering unique opportunities to fabricate porous magnesium scaffolds, current attempts to apply the AM approach to fabricating magnesium scaffolds still have some crucial limitations. This study demonstrated that the solvent-cast 3D printing technique presents unprecedented possibilities to fabricate Mg-based porous scaffolds. The judicious chosen of formulated binder system allowed for the negligible binder residue after debinding and the short-time liquid-phase sintering strategy led to a great success in sintering pure magnesium scaffolds. The resulting scaffolds with hierarchical and interconnected pores have great potential to be used as a bone-substituting material.@en

For the treatment of large bony defects, no perfect solution has been yet found, partially due to the unavailability of ideal bone implants. Additively manufactured (AM) biodegradable porous metals provide unprecedented opportunities to fulfil the requirements for ideal bone implants to be used in such treatments. Firstly, the multi-scale geometry of these implants can be customized to mimic the human bone in terms of both micro-architecture and mechanical properties. Secondly, a porous structure with interconnected pores possesses a larger surface area and is favorable for the adhesion and proliferation of bone cells. Finally, the biodegradation property could be exploited to maintain the structural integrity of the implant during the healing process while ensuring that the biomaterial disappears afterwards, paving the way for full bone regeneration.@en

An ideal bone substituting material should be bone-mimicking in terms of mechanical properties, present a precisely controlled and fully interconnected porous structure, and degrade in the human body to allow for full regeneration of large bony defects. However, simultaneously satisfying all these three requirements has so far been highly challenging. Here we present topologically ordered porous magnesium (WE43) scaffolds based on the diamond unit cell that were fabricated by selective laser melting (SLM) and satisfy all the requirements. We studied the in vitro biodegradation behavior (up to 4 weeks), mechanical properties and biocompatibility of the developed scaffolds. The mechanical properties of the AM porous WE43 (E = 700-800 MPa) scaffolds were found to fall into the range of the values reported for trabecular bone even after 4 weeks of biodegradation. Scanning electron microscopy (SEM), Fourier transform infrared spectroscopy (FTIR), electrochemical tests and μCT revealed a unique biodegradation mechanism that started with uniform corrosion, followed by localized corrosion, particularly in the center of the scaffolds. Biocompatibility tests performed up to 72 h showed level 0 cytotoxicity (according to ISO 10993-5 and -12), except for one time point (i.e., 24 h). Intimate contact between cells (MG-63) and the scaffolds was also observed in SEM images. The study shows for the first time that AM of porous Mg may provide distinct possibilities to adjust biodegradation profile through topological design and open up unprecedented opportunities to develop multifunctional bone substituting materials that mimic bone properties and enable full regeneration of critical-size load-bearing bony defects. Statement of Significance: The ideal biomaterials for bone tissue regeneration should be bone-mimicking in terms of mechanical properties, present a fully interconnected porous structure, and exhibit a specific biodegradation behavior to enable full regeneration of bony defects. Recent advances in additive manufacturing have resulted in biomaterials that satisfy the first two requirements but simultaneously satisfying the third requirement has proven challenging so far. Here we present additively manufactured porous magnesium structures that have the potential to satisfy all above-mentioned requirements. Even after 4 weeks of biodegradation, the mechanical properties of the porous structures were found to be within those reported for native bone. Moreover, our comprehensive electrochemical, mechanical, topological, and biological study revealed a unique biodegradation behavior and the limited cytotoxicity of the developed biomaterials.@en