The Oscillating Water Column (OWC) wave energy converter has been shown to have high potential, thus rendering extensive development in recent years. In order to further accelerate its development, highly accurate yet computationally efficient tools are necessary particularly when studying the interaction of multiple OWC devices. This paper proposes a new framework for fixed OWC devices with an orifice, that uses the input from a high fidelity non-linear numerical model to improve the accuracy of a low fidelity linear numerical model keeping computational costs low. This is done by accounting for the non-linearities in the pressure-flow of an orifice in the input to the linear numerical model. Experimental data is used to validate the framework, thus providing an accurate and computationally efficient linear numerical model, that can be used for the preliminary analysis of fixed OWC devices.@en

Utilization of Boundary Element Method (BEM) based on linear potential flow for modelling Oscillating Water Column (OWC) devices has gained popularity in the last two decades. The commercial BEM solver WAMIT has been used widely for modelling OWCs and validated using experimental modelling (Delauré et. al. 2003, Bingham et. al. 2015, Faÿ 2020). The open-source BEM solver NEMOH has however been mostly ineffective in modelling OWCs since the main approach adopted previously modelled the imaginary piston as a thin disk. In this research, the multi-body interaction problem has been adopted in modelling a box-type and bottom-detached OWC device in NEMOH, where the imaginary piston has been modelled to the length of the internal water column (Penalba et.al. 2017) and compared with experimental data. A further comparison is drawn with the numerical method of Computational Fluid Dynamics (CFD) , which has shown to be accurate for modelling OWC devices (Simonetti et. al. 2015), yet requires significantly higher computational resources than BEM. A two-dimensional CFD numerical wave tank, developed generating and absorbing waves with the waves2Foam toolbox (Jacobsen et al., 2012) of the open-source package OpenFOAM, is used for comparative purposes.@en

In this paper, a Reynolds-averaged Navier-Stokes (RANS) equations solver, interFoam of OpenFOAM®, is validated for wave interactions with a dike, including a promenade and vertical wall, on a shallow foreshore. Such a coastal defence system is comprised of both an impermeable dike and a beach in front of it, forming the shallow foreshore depth at the dike toe. This case necessitates the simulation of several processes simultaneously: wave propagation, wave breaking over the beach slope, and wave interactions with the sea dike, consisting of wave overtopping, bore interactions on the promenade, and bore impacts on the dike-mounted vertical wall at the end of the promenade (storm wall or building). The validation is done using rare large-scale experimental data. Model performance and pattern statistics are employed to quantify the ability of the numerical model to reproduce the experimental data. In the evaluation method, a repeated test is used to estimate the experimental uncertainty. The solver interFoam is shown to generally have a very good model performance rating. A detailed analysis of the complex processes preceding the impacts on the vertical wall proves that a correct reproduction of the horizontal impact force and pressures is highly dependent on the accuracy of reproducing the bore interactions.

@en

Three open source wave models are applied in 2DV to reproduce a large-scale wave flume experiment of bichromatic wave transformations over a steep-sloped dike with a mildly-sloped and very shallow foreshore: (i) the Reynolds-averaged Navier–Stokes equations solver interFoam of OpenFOAM® (OF), (ii) the weakly compressible smoothed particle hydrodynamics model DualSPHysics (DSPH) and (iii) the non-hydrostatic nonlinear shallow water equations model SWASH. An inter-model comparison is performed to determine the (standalone) applicability of the three models for this specific case, which requires the simulation of many processes simultaneously, including wave transformations over the foreshore and wave-structure interactions with the dike, promenade and vertical wall. A qualitative comparison is done based on the time series of the measured quantities along the wave flume, and snapshots of bore interactions on the promenade and impacts on the vertical wall. In addition, model performance and pattern statistics are employed to quantify the model differences. The results show that overall, OF provides the highest model skill, but has the highest computational cost. DSPH is shown to have a reduced model performance, but still comparable to OF and for a lower computational cost. Even though SWASH is a much more simplified model than both OF and DSPH, it is shown to provide very similar results: SWASH exhibits an equal capability to estimate the maximum quasi-static horizontal impact force with the highest computational efficiency, but does have an important model performance decrease compared to OF and DSPH for the force impulse.

@en

Growing energy demand has increased interest in marine renewable energy resources, i.e. wave energy which is harvested through Wave Energy Converter (WEC) Arrays.
However, the wave energy industry is currently at a significant juncture in its development, facing a number of challenges which require that research re-focuses on a holistic techno-economic perspective, where economics consider the full life-cycle costs of the technology. It also requires development of WECs suitable for niche markets, because in Europe there are inequalities regarding wave energy resources, wave energy companies, national programmes and investments. As a result, in Europe there are leading and non-leading countries in wave energy technology. The sector also needs to increase confidence of potential investors by reducing (non-)technological risks. This can be achieved through an interdisciplinary approach by involving engineers, economists, environmental scientists, legislation, governmental bodies and policy experts. Consequently, the wave energy sector needs to receive the necessary attention compared to other more advanced and commercial ocean energy technologies (e.g. offshore wind).
The formation of the first open pan-European Network on an interdisciplinary approach will contribute to largescale WEC Array deployment by dealing with the current bottlenecks. The WECANet European COST Action, introduced in September 2018 and presented in this paper, aims at a collaborative and inclusive approach, as it provides a strong networking platform that also creates the space for dialogue between all stakeholders in wave energy. An important characteristic of the Action is that participation is open to all parties interested and active in the development of wave energy. Previous activities organised by WECANet core group members have resulted in a number of joint European projects and scientific publications. WECANet’s main target is the equal research, training, networking, collaboration and funding opportunities for all researchers and professionals, regardless of age, gender and country in order to obtain understanding in the main challenges governing the development of the wave energy sector.@en

Overtopping bore impact forces on a dike mounted vertical wall were measured in similar large-scale (Froude length scale factor 1-to-4.3) and small-scale (Froude length scale factor 1-to-25) models. The differences due to scale effects were studied, by comparing the up-scaled force measurements from both models in prototype. It was noted that if a minimum layer thickness, velocity of the overtopping flow and water depth at the dike toe were maintained in the small-scale model, the resulting differences in impact force due to scale effects are within the range of differences due to non-repeatability and model effects.@en

Overtopping wave loads on vertical structures on top of a dike have been investigated in several small scale experiments in the past. A large-scale validation for a mild foreshore situation is still missing. Hence the WALOWA experimental campaign was carried out to address this topic. In the present paper the objectives of the WALOWA project are outlined in detail, the model and measurement set-up described and the test program presented. Furthermore, preliminary results featuring a single 1000 irregular waves test of the test program are highlighted. This includes the study of the mild and sandy foreshore evolution by comparing profiles before and after the test execution. The profile measurements are obtained with a mechanical profiler. The wave parameters offshore and at the dike toe are numerically simulated using a SWASH model. The numerical results are validated against the measurements. Finally, the force and pressure time series of the waves impacting against the wall are processed and filtered. The load cell measurements and the time series of integrated pressures are compared to each other and for each impact event the maximum force is derived.@en