One of the main problems of renewable energies is storage of the energy carrier. For long-term storage, solar fuels seem to be a good option. Direct solar water splitting could play an important role in the production of these solar fuels. One of the main challenges of this process is the charge separation and collection at the interfaces. The knowledge on photovoltaic (PV) junctions can be used to tackle this challenge. In this work, the use of doped layers to enhance the electric field in an a-SiC:H photocathode, and the use of thin-film silicon multijunction devices to achieve a stand-alone solar water splitting device are discussed. Using a p-i-n structure as a-SiC:H photocathode, a current density of 10mA/cm² is achievable. The p-i-n structure proposed also indicates the suitability of traditional PV structures for solar water splitting. In addition, hybrid devices, including a silicon heterojunction PV device, are proposed. A combination of the a-SiC:H photocathode with a nc-Si:H/c-Si is demonstrated and potential STH efficiencies of 7.9% have been achieved. Furthermore, a purely PV approach such as a triple junction a-Si:H/nc-Si:H/nc-Si:H solar cell is demonstrated, with solar-to-hydrogen (STH) efficiencies of 9.8%

Amorphous silicon carbide (a-SiC:H) is a promising material for photoelectrochemical water splitting owing to its relatively small band-gap energy and high chemical and optoelectrical stability. This work studies the interplay between charge-carrier separation and collection, and their injection into the electrolyte, when modifying the semiconductor/electrolyte interface. By introducing an n-doped nanocrystaline silicon oxide layer into a p-doped/intrinsic a-SiC:H photocathode, the photovoltage and photocurrent of the device can be significantly improved, reaching values higher than 0.8V. This results from enhancing the internal electric field of the photocathode, reducing the Shockley-Read-Hall recombination at the crucial interfaces because of better charge-carrier separation. In addition, the charge-carrier injection into the electrolyte is enhanced by introducing a TiO₂ protective layer owing to better band alignment at the interface. Finally, the photocurrent was further enhanced by tuning the absorber layer thickness, arriving at a thickness of 150nm, after which the current saturates to 10mAcm^-2 at 0V vs. the reversible hydrogen electrode in a 0.2m aqueous potassium hydrogen phthalate (KPH) electrolyte at pH4.

Metal-insulator-semiconductor (MIS) photoelectrodes offer a simple alternative to the traditional semiconductor-liquid junction and the conventional p-n junction electrode. Highly efficient MIS photoanodes require interfacial surface passivating oxides and high workfunction metals to produce a high photovoltage. Herein, we investigate and analyze the effect of interfacial oxides and metal workfunctions on the barrier height and the photovoltage of a c-Si photoanode. We use two metal components in a bimetal contact configuration and observe the modulation of the effective barrier height and the resulting photovoltage as a function of the secondary outer metal. The photovoltage shows a strong linear dependence by increasing the inner metal workfunction, with the highest photovoltage achieved by a MIS photoanode using a platinum inner metal. We also found that coupling a thin aluminium oxide with an interfacial silicon oxide and controlling the oxide thickness can significantly improve the photovoltage of an MIS junction photoanode.

Solar-assisted water splitting can potentially provide an efficient route for large-scale renewable energy conversion and storage. It is essential for such a system to provide a sufficiently high photocurrent and photovoltage to drive the water oxidation reaction. Here we demonstrate a photoanode that is capable of achieving a high photovoltage by engineering the interfacial energetics of metal-insulator-semiconductor junctions. We evaluate the importance of using two metals to decouple the functionalities for a Schottky contact and a highly efficient catalyst. We also illustrate the improvement of the photovoltage upon incidental oxidation of the metallic surface layer in KOH solution. Additionally, we analyse the role of the thin insulating layer to the pinning and depinning of Fermi level that is responsible to the resulting photovoltage. Finally, we report the advantage of using dual metal overlayers as a simple protection route for highly efficient metal-insulator-semiconductor photoanodes by showing over 200 h of operational stability.

Bismuth vanadate (BiVO₄) is one of the most efficient light absorbing metal oxides for solar water splitting. BiVO₄ photoanodes immersed in an electrolyte in an open circuit configuration and exposed to simulated solar illumination for prolonged time achieve superior photoelectrochemical (PEC) activity. This photocharging (PC) effect is capable of almost completely overcoming the surface and bulk limitations of BiVO₄. Herein we show that alkaline conditions favor the PC effect; specifically BiVO₄ photoanodes subjected to PC treatment at pH 10 achieve a record high photocurrent for undoped and uncatalyzed BiVO₄ of 4.3 mA cm^-2 @ 1.23 V_RHE, an outstandingly low onset potential of 0.25 V_RHE, and a very steep photocurrent onset. Alkaline conditions also facilitate excellent external and internal quantum efficiencies of 75 and 95% respectively (average in the 440 nm > λ > 330 nm range). Moreover, impedance spectroscopy and in situ XAS study suggest that electronic, structural and chemical properties of the bulk of these films remain unchanged during the PC treatment. However, appreciable changes in the surface-related properties take place. Ultimately, our results indicate that the improved activity of PC-BiVO₄ is enhanced by surface reaction pathways of the semiconductor-liquid junction, which is directly correlated with the electrochemical environment in which it is modified.

Photoelectrochemical (PEC) water splitting is a sustainable approach to produce a renewable fuel by harvesting the energy of the Sun to split water to form hydrogen and oxygen. In order to drive the water splitting reaction efficiently, substantial ohmic losses due to poor ionic conductivity of the electrolyte should be avoided, and therefore the reaction should be carried out at an extreme electrolyte pH. Herein we demonstrate the photoelectrochemical activity of an amorphous silicon carbide (a-SiC) photocathode for solar hydrogen evolution using an ultrathin nickel (Ni) film coupled with a nickel molybdenum catalyst (Ni-Mo) in a highly alkaline solution (pH 14). The incorporation of the Ni film coupled with Ni-Mo nanoparticles increases the number of active sites and therefore improves the kinetics of the hydrogen evolution reaction. Additionally, we report the influence of the catalyst configurations on the ohmic and solid liquid junction behavior on semiconducting interfacial layers. The a-SiC photocathode coated with the Ni/Ni-Mo dual-catalyst produces a photocurrent density of -14 mA cm^-2 at 0 V vs. RHE using only cheap and abundant materials. This photocurrent is the highest recorded value from an amorphous-Si-based photocathode, and is achieved with a total film thickness of less than 150 nm.