The effect of different alkali metal cations on the oxygen evolution activity and battery capacity of nickel electrodes has recently been studied in low concentration alkali hydroxide electrolytes. As high concentration hydroxide electrolytes are favored in applications due to their high conductivity, we investigate if the cation effects observed in low concentration electrolytes translate to more industrially relevant conditions for both alkaline water electrolysis and nickel iron batteries. We investigate the alkali metal cation effect on the electrochemical properties of nickel electrodes in highly concentrated hydroxide electrolytes by adding Li⁺, Na⁺, Cs⁺ and Rb⁺ cations to a 6.5 M KOH electrolyte, while keeping the hydroxide concentration constant. For OER we find a trend in activity similar to that at low concentrations Rb⁺>Cs⁺>K⁺>Na⁺>Li⁺, where especially larger additions of Rb⁺ and Cs⁺ (1 M or 0.5 M) cause a significant decrease in OER potential. Smaller cations interact with the layered hydroxide structures in NiOOH to stabilize the α/γ phases and increase the potential for OER. The intercalation of small cations also causes an increase in battery electrode capacity because of the higher average valence of the Ni(OH)2/NiOOH α/γ pair. Small concentrations of Li⁺ added to a concentrated KOH electrolyte can therefore be beneficial for the nickel electrode battery functionality and for an integrated battery and electrolyser system, where it increases the battery capacity without a significant increase in OER onset potential.

Both daily and seasonal fluctuations of renewable power sources will require large-scale energy storage technologies. A recently developed integrated battery and electrolyzer system, called battolyser, fulfills both time-scale requirements. Here, we develop a macroscopic COMSOL Multiphysics model to quantify the energetic efficiency of the battolyser prototype that, for the first time, integrates the functionality of a nickel-iron battery and an alkaline electrolyzer. The current prototype has a rated capacity of 5 Ah, and to develop a larger, enhanced system, it is necessary to characterize the processes occurring within the battolyser and to optimize the individual components of the battolyser. Therefore, there is a need for a model that can provide a fast screening on how the properties of individual components influence the overall energy efficiency of the battolyser prototype. The model is validated using experimental results, and new configurations are compared, and the energy efficiency is optimized for the scale-up of this lab-scale device. Based on the modeling work, we find an optimum electrode thickness for the nickel electrode of 3 and 2.25 mm for the iron electrode with optimal electrode porosities in the range of void fraction of 0.15-0.35. Additionally, electrolyte conductivity and the gap thickness are found to have a small effect on the overall efficiency of the device.

One of the main problems of renewable energies is storage of the energy carrier. For long-term storage, solar fuels seem to be a good option. Direct solar water splitting could play an important role in the production of these solar fuels. One of the main challenges of this process is the charge separation and collection at the interfaces. The knowledge on photovoltaic (PV) junctions can be used to tackle this challenge. In this work, the use of doped layers to enhance the electric field in an a-SiC:H photocathode, and the use of thin-film silicon multijunction devices to achieve a stand-alone solar water splitting device are discussed. Using a p-i-n structure as a-SiC:H photocathode, a current density of 10mA/cm² is achievable. The p-i-n structure proposed also indicates the suitability of traditional PV structures for solar water splitting. In addition, hybrid devices, including a silicon heterojunction PV device, are proposed. A combination of the a-SiC:H photocathode with a nc-Si:H/c-Si is demonstrated and potential STH efficiencies of 7.9% have been achieved. Furthermore, a purely PV approach such as a triple junction a-Si:H/nc-Si:H/nc-Si:H solar cell is demonstrated, with solar-to-hydrogen (STH) efficiencies of 9.8%

Amorphous silicon carbide (a-SiC:H) is a promising material for photoelectrochemical water splitting owing to its relatively small band-gap energy and high chemical and optoelectrical stability. This work studies the interplay between charge-carrier separation and collection, and their injection into the electrolyte, when modifying the semiconductor/electrolyte interface. By introducing an n-doped nanocrystaline silicon oxide layer into a p-doped/intrinsic a-SiC:H photocathode, the photovoltage and photocurrent of the device can be significantly improved, reaching values higher than 0.8V. This results from enhancing the internal electric field of the photocathode, reducing the Shockley-Read-Hall recombination at the crucial interfaces because of better charge-carrier separation. In addition, the charge-carrier injection into the electrolyte is enhanced by introducing a TiO₂ protective layer owing to better band alignment at the interface. Finally, the photocurrent was further enhanced by tuning the absorber layer thickness, arriving at a thickness of 150nm, after which the current saturates to 10mAcm^-2 at 0V vs. the reversible hydrogen electrode in a 0.2m aqueous potassium hydrogen phthalate (KPH) electrolyte at pH4.