For battery architectures that need a solid ion conductor with good contacting performance and high stability against electrochemical oxidation, polymerized ionic liquids (PIL) pose a valuable class of materials. The low conductivity of the binary PIL/ lithium salt system can be increased using a ternary ionic liquid acting as plasticiser. The conductive mechanism of the ternary system is however not fully understood. This work shows the shift in conduction mechanism for the ternary Li−/[1,3]PYR-/PDADMA-FSI system by increasing the lithium salt concentration and comparing the transfer mechanism to binary ionic liquid (IL) electrolyte analogues using pulsed field gradient (PFG) nuclear magnetic resonance (NMR), NMR relaxometry, Raman spectroscopy and electrochemical techniques. Two conducting regimes were found which show a strong trade-off between conductivity and transference number. In the low lithium salt regime (≤35 wt% LiFSI), cluster diffusion of aggregated lithium is the dominating mechanism leading to low transference numbers (0.04–0.15 at room temperature (RT)). The high salt regime (≥50 wt% LiFSI) shows diffusion through free lithium ion hopping transfer, which has a stronger dependence on temperature and yields higher transference numbers (0.31 at RT). Increasing lithium salt concentration shows an inverse linear correlation with conductivity. The electrochemical characteristics of ternary IL/PIL/lithium salt are shown to be highly tuneable by varying the lithium salt fraction, while it maintains excellent characteristics like processability, stability and mechanical function.

There is an urge for rapid change in our energy system as several deadlines for agreements on climate change mitigation goals are near, with the final deadline being 2050 to achieve the formidable task of realization of a CO2 neutral society. There are viable solutions to redesign our energy system through renewables, but the cost of such a redesign will only be more steep if carried out short before the deadline. From 2025 every year 4% of our energy system needs to be replaced using a simple linear approach, a percentage that will grow if we postpone it.
This work gives a clear insight in our current energy consumption behavior and the scale of our energy need. It provides possible improvements for specifically lithium batteries with liquid/polymerized liquid electrolytes. Currently it appears sodium battery chemistry is promising to be integrated in a completely renewable energy system. Fortunately the ‘lessons learned’ in this work are usable for research in sodium type of chemistry, because the fundamental mechanisms of intercalation, conductivity and redox activity are similar.

The growing demand for safe, cost-efficient, high-energy and high-power electrochemical energy storage devices has stimulated the development of aqueous-based supercapacitors with high capacitance, high rate capability, and high voltage. 2D titanium carbide MXene-based electrodes have shown excellent rate capability in various dilute aqueous electrolytes, yet their potential window is usually narrower than 1.2 V. In this study, we show that the potential window of Ti₃C₂T _x MXene can be efficiently widened to 1.5 V in a cost-effective and environmentally benign polyethylene glycol (PEG) containing molecular crowding electrolyte. Additionally, a pair of redox peaks at −0.25 V/−0.05 V vs. Ag (cathodic/anodic) emerged in cyclic voltammetry after the addition of PEG, yielding an additional 25% capacitance. Interestingly, we observed the co-insertion of the molecular crowding agent PEG-400 during the Li⁺ intercalation process based on in-situ x-ray diffraction analysis. As a result, Ti₃C₂T _x electrodes presented an interlayer space change of 4.7 Å during a complete charge/discharge cycle, which is the largest reversible interlayer space change reported so far for MXene-based electrodes. This work demonstrates the potential of adding molecular crowding agents to improve the performance of MXene electrodes in aqueous electrolytes and to enlarge the change of the interlayer spacing.

Increasing the electrode thickness, thereby reducing the proportion of inactive cell components, is one way to achieve higher-energy-density lithium-ion batteries. This, however, results in higher electronic and ionic overpotentials and/or mechanical failure induced by binder migration. Here, we report ethanol-induced phase inversion as an effective method for making high-mass-loading nickel-rich, layered oxide (LiNi0.8Mn0.1Co0.1O2 [NMC811]) electrodes. The ethanol-induced phase inversion electrodes significantly outperform their conventionally processed counterparts with similar loading (35 mg/cm2) and porosity (30%) in Li/NMC half-cells (131.7 mAh/g vs. 56.7 mAh/g) at 1C (7 mA/cm2) discharge. The binder structure induced by the nonsolvent improves the pore connectivity and results in lower tortuosity factors. The rapid solvent removal reduces the binder migration during drying, enabling ultrahigh active mass loadings up to 60 mg/cm2 (12 mAh/cm2). Further, the compatibility of the phase inversion process with current roll-to-roll coating setups makes this a processing technique with high industrial feasibility.

Solid-state batteries with lithium metal anodes are considered the next major technology leap with respect to today’s lithium-ion batteries, as they promise a significant increase in energy density. Expectations for solid-state batteries from the automotive and aviation sectors are high, but their implementation in industrial production remains challenging. Here, we report a solid-state lithium–metal battery enabled by a polymer electrolyte consisting of a poly(DMADAFSI) cationic polymer and LiFSI in Pyr13FSI as plasticizer. The polymer electrolyte is infiltrated and solidified in the pores of a commercial LiNi0.8Mn0.1Co0.1O2 (NMC811) cathode with up to 2.8 mAh cm–2 nominal areal capacity and in the pores of a 25 μm thin commercial polypropylene separator. Cathode and separator are finally laminated into a cell in combination with a commercial 20 μm thin lithium metal anode. Our demonstration of a solid-state polymer battery cycling at full nominal capacity employing exclusively commercially available components available at industrial scale represents a critical step forward toward the commercialization of a competitive all-solid-state battery technology.

Nanostructured solid composite electrolyte or nano-SCE, which is composed of an ionic liquid, nanoporous silica, and residuals of immobilized precursor components, shows promising synergistic properties. The ionic conductivity of nano-SCE is in the range of 2–5 mS cm⁻¹, which exceeds the bulk ionic liquid conductivity at ambient temperature, while maintaining characteristics of a solid electrolyte such as having no leakage issues as the ionic liquid is confined, and lower flammability compared to conventional liquid electrolytes. In this study, the underlying mechanism of enhanced conductivity is investigated by using magic angle spinning NMR and NMR relaxometry analysis. Water, one of the volatile precursor molecules has shown to play a key role in the final conductivity and stability at the solid-electrolyte interface, as it enhances the temperature range in which the ionic liquid remains mobile. In line with previous studies, water with lowered mobility is found in the silicon matrix. The activation energies of lithium ion transfer probed by NMR relaxometry, however, do not change as function of water content. The increase in bulk mobility of lithium ions under ambient conditions compared to water-less nano-SCE is found to be the origin of the altered conductivity of this material.