The continuing drive to miniaturise electronic devices requires an understanding of how the materials in these devices behave under stress, particularly with respect to electromigration. In this study, we explore the relationship between the microstructure of copper (Cu) and electromigration by using an approach that combines in situ Scanning Electron Microscopy (SEM) with Electron Backscatter Diffraction (EBSD). This in-situ SEM-EBSD technique enables real-time observation and analysis of electromigration-induced microstructure changes. Our investigation provides detailed insights into the microstructure effect on electromigration. Specifically, samples annealed at 300 °C showed void formation after the electromigration test and higher Kernal average misorientation (KAM) values, indicating higher internal strains and an inhomogeneous microstructure. In contrast, samples annealed at 500 °C maintained lower KAM values with minimal changes in crystal orientation, highlighting a more stable and uniform electromigration-resistant microstructure. Our results demonstrate the critical role of microstructure in determining the electromigration resistance of copper interconnects. By optimizing the annealing temperature, the reliability of the copper microstructure can be significantly improved by reducing the dislocations and increasing grain size, thus extending its lifetime.

As the dimensions of interconnects in integrated circuits continue to shrink, an urgent need arises to understand the physical mechanism associated with electromigration. Using x-ray nanodiffraction, we analyzed the stresses in Blech-structured pure Cu lines subjected to different electromigration conditions. The results suggest that the measured residual stresses in the early stages of electromigration are related to relaxation of stresses caused by thermal expansion mismatch, while a developing current-induced stress leads to reductions in the residual stress after longer test times. These findings not only validate the feasibility of measuring stress in copper lines using nanodiffraction but also highlight the need for a further understanding, particularly through in situ electromigration experiments with x-ray nanodiffraction analysis.

This paper presented integrated electromigration (EM) studies through experiment, theory, and simulation. First, extensive EM tests were performed using Blech and standard wafer-level electromigration acceleration test (SWEAT)-like structures, which were fabricated on four-inch wafers. Second, a molecular dynamics (MD) simulation-based diffusion-induced strain was incorporated into the existing coupled theory. Third, one-dimensional (1D) governing equations in terms of atomic concentration for un-passivated and passivated configurations were derived for void formation and growth, using a modified Eshelby's solution to consider the effect of passivation. Fourth, a systematic approach was established, including theoretical formulations and experimental methods, to obtain key material properties, i.e., critical atomic concentration and diffusivity. We then determined the material's properties from a specific set of experimental data, using aluminium (Al) as a carrier for demonstration. These properties were then used to predict the time to failure and void growth under various conditions. The theoretical results agreed well with the experimental data. Moreover, we theoretically determined the critical threshold products of current density and conductor length for the un-passivated and passivated configurations, respectively. Both experiment and theory showed that, in the absence of mechanical stress in un-passivated configurations, the atomic self-diffusion, which was opposite to electron wind, was significant in resisting EM development. However, when mechanical stress was present, such as in passivated configurations, stress migration played a dominant role in resisting EM development. Our numerical results showed that the current density exponent n in Black's law remained as 2 in the range of the current density greater than 0.2 MA/cm² and rapidly approached infinity at a low level of current density.

This paper presented a comprehensive experimental and simulation study for thermomigration (TM) accompanying electromigration (EM) at elevated current densities. Both Blech and standard wafer-level electromigration acceleration test (SWEAT)-like test structures, with aluminum (Al) as a carrier, were used for testing and analysis. In Part I of our study (Cui et al., 2023a), the experimental and numerical results with the current density of 1 MA/cm² were presented. We observed that Al stripes with a SWEAT structure did not show damage in the entire length, while Blech structures showed void and hillock formations only at the cathode and anode, respectively. The temperature gradient owing to Joule heating was neglected in our previous simulations, and the predicted results agreed well with the experimental observations. However, we have not theoretically verified the effect of the temperature gradient. In this paper, we first reported the new experimental data under the elevated current densities of 3 and 5 MA/cm². In both Blech and SWEAT structures, the spreading of voids in the middle region of conductors was observed. Moreover, in Blech structures, voiding in the middle region occurred after a period of time when voids/hillocks were formed at the cathode and anode, while the SWEAT structures did not show damage at the two ends. Next, based on the coupled 3D theory (Cui et al., 2023a), new analytical one-dimensional (1D) solutions were derived for the Blech and SWEAT structures in the un-passivated configuration considering TM. We found that TM played a significant role in the EM development in the middle of conductors under the elevated current density. The numerical results were in excellent agreement with the experimental data with the consideration of TM. We further established new EM failure's threshold criteria for the SWEAT structures in the form of the product of current density and square of conductor length. This is a major departure from the original Blech's theory in which only mechanical stress gradient was considered. We also studied the acceleration factor of the current density exponent and presented an insight into failure mechanisms associated with TM.

In this work, a highly linear temperature sensor based on a silicon carbide (SiC) p-n diode is presented. Under a constant current biasing, the diode has an excellent linear response to the temperature (from room temperature to 600°C). The best linearity (coefficient of determination ${R}^{{2}}$ = 99.98%) is achieved when the current density is 0.53 mA/cm2. The maximum sensitivity of the p-n diode is 3.04 mV/°C. The temperature sensor is fully compatible with Fraunhofer Institute (FHG) IISB's open SiC CMOS (complementary metal-oxide-semiconductor) technology, thus enabling the monolithic integration with SiC readout circuits for high-temperature applications. The sensor also features a simple fabrication process. To our knowledge, the presented device is the first SiC diode temperature sensor that does not require a mesa etch or backside contacts.

The continuous downscaling of microelectronics has introduced many reliability issues on interconnect. Electromigration and dewetting are major reliability concerns in high-temperature micro- and nanoscale devices. In this paper, the local dewetting of copper thin film during the electromigration test was first found and investigated. When the high current was applied, the dewetted copper forming around the edge was observed at the cathode of the conductor. Furthermore, the effect of temperature and conductor size on local dewetting was investigated. Our proposed mechanism for local dewetting is in good agreement with experimental findings.

Understanding the atomic diffusion features in metallic material is significant to explain the diffusion-controlled physical processes. In this paper, using electromigration experiments and molecular dynamic (MD) simulations, we investigate the effects of grain size and temperature on the self-diffusion of polycrystalline aluminium (Al). The mass transport due to electromigration are accelerated by increasing temperature and decreasing grain size. Magnitudes of effective diffusivity (Deff) and grain boundary diffusivity (DGBs) are experimentally determined, in which theDeffchanges as a function of grain size and temperature, butDGBsis independent of the grain size, only affected by the temperature. Moreover, MD simulations of atomic diffusion in polycrystalline Al demonstrate those observations from experiments. Based on MD results, the Arrhenius equation ofDGBsand empirical formula of the thickness of grain boundaries at various temperatures are obtained. In total,DeffandDGBsobtained in the present study agree with literature results, and a comprehensive result of diffusivities related to the grain size is presented.