The original version of this article contained errors in Figure 3a and Figure 3f. In Figure 3a, the activation energies (Ea) were calculated using a log scale instead of a logarithm ln scale. In Figure 3f, the y-axis interval was not properly selected. The correct y-axis interval in Figure 3f and the numerical values of the activation energy are now provided in Figure 3a and the main text. These errors have been corrected in the HTML and PDF versions of the article.@en

Sodium-ion batteries have not only garnered substantial attention for grid-scale energy storage owing to the higher abundance of sodium compared with lithium, but also present the possibility of fast charging because of the inherently higher sodium-ion mobility. However, it remains a phenomenal challenge to achieve a combination of these merits, given the complex structural chemistry of sodium-ion oxide materials. Here we show that O3-type sodium-ion layered cathodes (for example, Na5/6Li2/27Ni8/27Mn11/27Ti6/27O2) have the potential to attain high power density, high energy density (260 Wh kg−1 at the electrode level) and long cycle life (capacity retention of 80% over 700 cycles in full cells). The design involves introduction of characteristic P3-structural motifs into an O3-type framework that serves to promote sodium-ion diffusivity and address detrimental transition metal migration and phase transition at a high state of charge. This study provides a principle for the rational design of sodium-ion layered oxide electrodes and advances the understanding of the composition–structure–property relationships of oxide cathode materials.@en

A key challenge for solid-state-batteries development is to design electrode-electrolyte interfaces that combine (electro)chemical and mechanical stability with facile Li-ion transport. However, while the solid-electrolyte/electrode interfacial area should be maximized to facilitate the transport of high electrical currents on the one hand, on the other hand, this area should be minimized to reduce the parasitic interfacial reactions and promote the overall cell stability. To improve these aspects simultaneously, we report the use of an interfacial inorganic coating and the study of its impact on the local Li-ion transport over the grain boundaries. Via exchange-NMR measurements, we quantify the equilibrium between the various phases present at the interface between an S-based positive electrode and an inorganic solid-electrolyte. We also demonstrate the beneficial effect of the LiI coating on the all-solid-state cell performances, which leads to efficient sulfur activation and prevention of solid-electrolyte decomposition. Finally, we report 200 cycles with a stable capacity of around 600 mAh g−1 at 0.264 mA cm−2 for a full lab-scale cell comprising of LiI-coated Li2S-based cathode, Li-In alloy anode and Li6PS5Cl solid electrolyte.@en

High-entropy alloys/compounds have large configurational entropy by introducing multiple components, showing improved functional properties that exceed those of conventional materials. However, how increasing entropy impacts the thermodynamic/kinetic properties in liquids that are ambiguous. Here we show this strategy in liquid electrolytes for rechargeable lithium batteries, demonstrating the substantial impact of raising the entropy of electrolytes by introducing multiple salts. Unlike all liquid electrolytes so far reported, the participation of several anionic groups in this electrolyte induces a larger diversity in solvation structures, unexpectedly decreasing solvation strengths between lithium ions and solvents/anions, facilitating lithium-ion diffusivity and the formation of stable interphase passivation layers. In comparison to the single-salt electrolytes, a low-concentration dimethyl ether electrolyte with four salts shows an enhanced cycling stability and rate capability. These findings, rationalized by the fundamental relationship between entropy-dominated solvation structures and ion transport, bring forward high-entropy electrolytes as a composition-rich and unexplored space for lithium batteries and beyond.@en

To realize concurrently the high-energy density and excellent cycling stability, maximum utilization of redox couple, minimization of detrimental phase transition, and structural degradation of O3-type layered oxide cathodes are critical for developing Na-ion batteries. Ni2+/Ni4+ redox couple showing multielectron reaction and higher redox potential is favorable to increase the energy density. However, the Jahn-Teller distortion of Ni3+ generated upon (dis)charging results in a strong anisotropy in the local crystal structure that causes irreversible interlayer bending and chemo-mechanical cracks of the cathode particles, compromising the electrochemical properties eventually. In this work, we show a slight multielement doping strategy that enlarges the amount of active redox components while minimizing the inactive contents. The results show that the uniform distribution of multiple components can help increase the disorder degree of atom arrangement and alleviate the structural changes and detrimental anisotropy cracks. As a proof of concept, a multielement-doped O3-type Na0.9Ni0.25Cu0.05Mg0.05Zn0.05Fe0.05Al0.05Mn0.40Ti0.05Sn0.05O2 oxide is rationally prepared that presents better chemo-mechanical stability and delayed O3-P3 phase transition behavior. Compared to the high Ni-content Na0.9Ni0.35Fe0.2Mn0.45O2 cathode, this as-prepared multielement material delivers a reversible capacity of about 120 mAh/g in the voltage range of 2-4.0 V, superior cycling stability with 90% of capacity retention after 500 cycles, and excellent rate capability (more than 70% of initial capacity at 5.0 C). This work indicates that the multielement doping method is highly suitable for the development of advanced Na-ion layered oxide cathodes.@en

Developing liquid electrolytes with higher kinetics and enhanced interphase stability is one of the key challenges for lithium batteries. However, the poor solubility of lithium salts in solvents sets constraints that compromises the electrolyte properties. Here, it is shown that introducing multiple salts to form a high-entropy solution, alters the solvation structure, which can be used to raise the solubility of specific salts and stabilize electrode–electrolyte interphases. The prepared high-entropy electrolytes significantly enhance the cycling and rate performance of lithium batteries. For lithium-metal anodes the reversibility exceeds 99%, which extends the cycle life of batteries even under aggressive cycling conditions. For commercial batteries, combining a graphite anode with a LiNi0.8Co0.1Mn0.1O2 cathode, more than 1000 charge–discharge cycles are achieved while maintaining a capacity retention of more than 90%. These performance improvements with respect to regular electrolytes are rationalized by the unique features of the solvation structure in high-entropy electrolytes. The weaker solvation interaction induced by the higher disorder results in improved lithium-ion kinetics, and the altered solvation composition leads to stabilized interphases. Finally, the high-entropy, induced by the presence of multiple salts, enables a decrease in melting temperature of the electrolytes and thus enables lower battery operation temperatures without changing the solvents.@en

Recently, the all-d-metal Ni(Co)MnTi based Heusler compounds are found to have a giant magnetocaloric effect (GMCE) near room temperature and manifest different functionalities like multicaloric effects, which can be employed for solid-state refrigeration. However, in comparison to other traditional Heusler compounds, the relatively large thermal hysteresis (ΔThys) and moderately steep ferromagnetic phase transition provides limitations for real applications. Here, we present that fast solidification (suction casting) can sufficiently tailor the GMCE performance by modifying the microstructure. Compared with the arc-melted sample, the magnetic entropy change of the suction-casted sample shows a 67% improvement from 18.4 to 29.4 Jkg−1K−1 for a field change (∆μ0H) of 5 T. As the thermal hysteresis has maintained a low ΔThys value (5.5 K) for the enhanced first-order phase transition, a very competitive reversible magnetic entropy change of 21.8 Jkg−1K−1 for ∆μ0H = 5 T is obtained. Combining high-resolution transmission electron microscopy (HRTEM) and positron annihilation spectroscopy (PAS) results, the difference in lattice defect concentration is found to be responsible for the significant improvement in GMCE for the suction-cast sample, which suggests that defect engineering can be applied to control the GMCE. Our study reveals that fast solidification can effectively regulate the magnetocaloric properties of all-d-metal NiCoMnTi Heusler compounds without sacrificing ΔThys.@en

Lithium metal with its high theoretical capacity and low negative potential is considered one of the most important candidates to raise the energy density of all-solid-state batteries. However, lithium filament growth and its induced solid electrolyte decomposition pose severe challenges to realize a long cycle life. Here, dendrite growth in solid-state Li metal batteries is alleviated by introducing a high dielectric material, barium titanate, as a filler that removes the electric field gradients that catalyze dendrite formation. In symmetrical Li-metal cells, this results in a very small over-potential of only 48 mV at a relatively high current density of 1 mA cm−2, when cycling a capacity of 2 mA h cm−2 during 1700 h. The high dielectric filler improves the Coulombic efficiency and cycle life of full cells and suppresses electrolyte decomposition as indicated by solid-state nuclear magnetic resonance (NMR) and X-ray photoelectron spectroscopy (XPS) measurements. This indicates that the high dielectric filler can suppress dendrite formation, thereby reducing solid electrolyte decomposition reactions, resulting in the observed low overpotentials and improved cycling efficiency.@en

Layered O3-type oxides are one of the most promising cathode materials for Na-ion batteries owing to their high capacity and straightforward synthesis. However, these materials often experience irreversible structure transitions at elevated cutoff voltages, resulting in compromised cycling stability and rate performance. To address such issues, understanding the interplay of the composition, structure, and properties is crucial. Here, we successfully introduced a P-type characteristic into the O3-type layered structure, achieving a P3-dominated solid-solution phase transition upon cycling. This modification facilitated a reversible transformation of the O3-P3-P3′ structure with minimal and gradual volume changes. Consequently, the Na0.75Ni0.25Cu0.10Fe0.05Mn0.15Ti0.45O2 cathode exhibited a specific capacity of approximately 113 mAh/g, coupled with exceptional cycling performance (maintaining over 70% capacity retention after 900 cycles). These findings shed light on the composition-structure-property relationships of Na-ion layered oxides, offering valuable insights for the advancement of Na-ion batteries.@en

Layered O3-type oxides are one of the most promising cathode materials for Na-ion batteries owing to their high capacity and straightforward synthesis. However, these materials often experience irreversible structure transitions at elevated cutoff voltages, resulting in compromised cycling stability and rate performance. To address such issues, understanding the interplay of the composition, structure, and properties is crucial. Here, we successfully introduced a P-type characteristic into the O3-type layered structure, achieving a P3-dominated solid-solution phase transition upon cycling. This modification facilitated a reversible transformation of the O3-P3-P3′ structure with minimal and gradual volume changes. Consequently, the Na0.75Ni0.25Cu0.10Fe0.05Mn0.15Ti0.45O2 cathode exhibited a specific capacity of approximately 113 mAh/g, coupled with exceptional cycling performance (maintaining over 70% capacity retention after 900 cycles). These findings shed light on the composition-structure-property relationships of Na-ion layered oxides, offering valuable insights for the advancement of Na-ion batteries.@en

Improving the reversibility of lithium metal batteries is one of the challenges in current battery research. This requires better fundamental understanding of the evolution of the lithium deposition morphology, which is very complex due to the various parameters involved in different systems. Here, we clarify the fundamental origins of lithium deposition coverage in achieving highly reversible and compact lithium deposits, providing a comprehensive picture in the relationship between the lithium microstructure and solid electrolyte interphase (SEI) for lithium metal batteries. Systematic variation of the salt concentration offers a framework that brings forward the different aspects that play a role in cycling reversibility. Higher nucleation densities are formed in lower concentration electrolytes, which have the advantage of higher lithium deposition coverage; however, it goes along with the formation of an organic-rich instable SEI which is unfavorable for the reversibility during (dis)charging. On the other hand, the growth of large deposits benefiting from the formation of an inorganic-rich stable SEI is observed in higher concentration electrolytes, but the initial small nucleation density prevents full coverage of the current collector, thus compromising the plated lithium metal density. Taking advantages of the paradox, a nanostructured substrate is rationally applied, which increases the nucleation density realizing a higher deposition coverage and thus more compact plating at intermediate concentration (∼1.0 M) electrolytes, leading to extended reversible cycling of batteries. @en

Nickel-rich layered oxide cathodes promise ultrahigh energy density but is plagued by the mechanical failure of the secondary particle upon (de)lithiation. Existing approaches for alleviating the structural degradation could retard pulverization, yet fail to tune the stress distribution and root out the formation of cracks. Herein, we report a unique strategy to uniformize the stress distribution in secondary particle via Kirkendall effect to stabilize the core region during electrochemical cycling. Exotic metal/metalloid oxides (such as Al2O3 or SiO2) is introduced as the heterogeneous nucleation seeds for the preferential growth of the precursor. The calcination treatment afterwards generates a dopant-rich interior structure with central Kirkendall void, due to the different diffusivity between the exotic element and nickel atom. The resulting cathode material exhibits superior structural and electrochemical reversibility, thus contributing to a high specific energy density (based on cathode) of 660 Wh kg−1 after 500 cycles with a retention rate of 86%. This study suggests that uniformizing stress distribution represents a promising pathway to tackle the structural instability facing nickel-rich layered oxide cathodes.@en

All-solid-state lithium batteries have attracted widespread attention for next-generation energy storage, potentially providing enhanced safety and cycling stability. The performance of such batteries relies on solid electrolyte materials; hence many structures/phases are being investigated with increasing compositional complexity. Among the various solid electrolytes, lithium halides show promising ionic conductivity and cathode compatibility, however, there are no effective guidelines when moving toward complex compositions that go beyond ab-initio modeling. Here, we show that ionic potential, the ratio of charge number and ion radius, can effectively capture the key interactions within halide materials, making it possible to guide the design of the representative crystal structures. This is demonstrated by the preparation of a family of complex layered halides that combine an enhanced conductivity with a favorable isometric morphology, induced by the high configurational entropy. This work provides insights into the characteristics of complex halide phases and presents a methodology for designing solid materials.@en

Ordered layered structures serve as essential components in lithium (Li)-ion cathodes1–3. However, on charging, the inherently delicate Li-deficient frameworks become vulnerable to lattice strain and structural and/or chemo-mechanical degradation, resulting in rapid capacity deterioration and thus short battery life2,4. Here we report an approach that addresses these issues using the integration of chemical short-range disorder (CSRD) into oxide cathodes, which involves the localized distribution of elements in a crystalline lattice over spatial dimensions, spanning a few nearest-neighbour spacings. This is guided by fundamental principles of structural chemistry and achieved through an improved ceramic synthesis process. To demonstrate its viability, we showcase how the introduction of CSRD substantially affects the crystal structure of layered Li cobalt oxide cathodes. This is manifested in the transition metal environment and its interactions with oxygen, effectively preventing detrimental sliding of crystal slabs and structural deterioration during Li removal. Meanwhile, it affects the electronic structure, leading to improved electronic conductivity. These attributes are highly beneficial for Li-ion storage capabilities, markedly improving cycle life and rate capability. Moreover, we find that CSRD can be introduced in additional layered oxide materials through improved chemical co-doping, further illustrating its potential to enhance structural and electrochemical stability. These findings open up new avenues for the design of oxide cathodes, offering insights into the effects of CSRD on the crystal and electronic structure of advanced functional materials.@en

Ordered layered structures serve as essential components in lithium (Li)-ion cathodes1–3. However, on charging, the inherently delicate Li-deficient frameworks become vulnerable to lattice strain and structural and/or chemo-mechanical degradation, resulting in rapid capacity deterioration and thus short battery life2,4. Here we report an approach that addresses these issues using the integration of chemical short-range disorder (CSRD) into oxide cathodes, which involves the localized distribution of elements in a crystalline lattice over spatial dimensions, spanning a few nearest-neighbour spacings. This is guided by fundamental principles of structural chemistry and achieved through an improved ceramic synthesis process. To demonstrate its viability, we showcase how the introduction of CSRD substantially affects the crystal structure of layered Li cobalt oxide cathodes. This is manifested in the transition metal environment and its interactions with oxygen, effectively preventing detrimental sliding of crystal slabs and structural deterioration during Li removal. Meanwhile, it affects the electronic structure, leading to improved electronic conductivity. These attributes are highly beneficial for Li-ion storage capabilities, markedly improving cycle life and rate capability. Moreover, we find that CSRD can be introduced in additional layered oxide materials through improved chemical co-doping, further illustrating its potential to enhance structural and electrochemical stability. These findings open up new avenues for the design of oxide cathodes, offering insights into the effects of CSRD on the crystal and electronic structure of advanced functional materials.@en